All these strengths combined make GTK+ a solid base for software development.

The Method of Creating Gtk+ Widgets in Linux Application Development

在Linux应用开发中创建Gtk+构件的方法

It would fit better in a more general discussion of Gtk development.

这些代码更适合针对Gtk开发的更全面讨论。

Application Study of development kit gtk+ technique on Linux GUI

Linux GUI开发工具Gtk+技术应用研究

Developing Communication Monitor System of Cluster Network with Python and GTK

用Python+GTK开发机群网络通信监控系统

The model for GTK+ geometry management consists of two phases

GTK+几何结构管理模型由两个阶段组成

Design Method of Asphalt Mixture Based on Performance& Brief Introduction of GTM Method

基于性能的沥青混合料设计方法&GTM方法简介

Analysis of Multi-dimensional Regional Traffic State Based on GTM Algorithm

基于GTM算法的多维区域交通状态分析

On Influence Factors to Asphalt Mixture Service Performance Designed by GTM

采用GTM设计的沥青混合料路用性能影响因素

Concrete construction quality control by use of GTM technology

浅析GTM设计的沥青混凝土施工质量控制

In this paper, a large number of different materials are selected to do the small punch test. A deeply research was carried out about GTN model, equivalent stress and strain in finite element simulation of the small punch test.

本文在进行大量小冲杆试验的基础上，对小冲杆试验的有限元模拟中GTN模型及等效应力应变关系进行了深入的研究。

In this paper, the finite element method based on GTN model is used to investigate the ductile crack growth behavior in the three-point bending specimens of the dissimilar metal welded joint.

本文采用内嵌GTN损伤模型的有限元方法，建立了核电异种金属焊接接头三点弯曲试样的有限元模型，数值模拟延性裂纹的起裂和扩展行为。

Study on the shrinkage deformation of thin composite laminates during curing process ductile damage analysis for fracture in sheet metal forming based on GTN mesoscopic damage model

复合材料薄板的成型固化收缩变形研究基于GTN细观损伤模型的板料成形过程损伤分析

There is more error in simulating void growth under unaxisymmetry triaxial stress conditions using R-T model and GTN model.

用R-T模型、GTN模型模拟非轴对称三轴应力状态下材料微孔洞损伤演化有较大的误差。

It was reported that using the PEA protocol as the first choice for high-risk GTN, and had achieve good effect.

有报道使用PEA方案作为高危GTN的首选治疗方案，取得良好的疗效。

Combining the experimental tensile test and finite element simulation, the inverse method is carried out to identify the GTN damage parameters.

采用逆向方法，将单向拉伸试验与有限元数值模拟相结合来确定GTN模型损伤参数。

Ductile damage analysis for fracture in sheet metal forming based on GTN mesoscopic damage model

基于GTN细观损伤模型的板料成形过程损伤分析

Brief discussion about the application of GTS-311d total station in canal construction

浅谈GTS-311D型全站仪在运河施工测量中的应用

Development of Software for GTS 126 Paging Services

GTS-126寻呼系统软件开发

Application of the Combination of SCS Software and GTS 211 D on Field Survey

SCS软件与GTS211D全站仪相结合在测量中的应用

DRAWING MAP WITH GTS AND PLANE TABLE New methods for surveying the plane curves

全站仪与平板仪相结合测绘地图平面曲线详测新法