Camber is the inward or outward tilt of the wheel at top.

The thermal camber of rolls is a very important factor affecting distribution of hot strip mills.

轧辊热凸度是影响热带钢连轧机负载辊缝的重要因素,高效率的工作辊冷却水系统是生产高质量热轧板带的重要保证.

At present , the experience method of installing the camber has many problems.

经验法设置大跨径连续刚构桥预拱度存在诸多问题.

The joint of all the camber will be the camber curve.

各截面凸度连线便是凸度曲线.

The method also permits inverse design with flaps , specification of geometric constraints ( thickness , camber, etc. ).

比如开发了边界层的形状参数,可以指定允许的最高表面上取消或延期举办层流 、 乎设计要求.

It has two sides, one is a circle, the other is a camber.

生:圆锥有两个面, 一个面是圆形, 另一个面是曲面.

Determine the camber factor.

确定曲面的因素.

I can see a point, a circle and a camber.

生:有一个点, 有一个圆,还有一个曲面.

The superstructure a depth of 3 ft . 6 in. a marked camber of 19 ft . 8 in.

上部结构的建筑高度为3英尺6 英寸,有19英尺8 英寸 显著的上拱度.

Long lengths of unsupported strip camber tend to deviate from the horizontal or slope to side.

长距离无支持的钢带偏离水平线或偏向一侧.也可参见以下部分.

" To Camber Company, please . It's on 32 nd avenue . "

去 坎培克斯 公司. 在第32街上.

Inward tilt is negative camber and outward tilt is positive camber.

向内倾斜,是消极的拱和拱向外倾斜是积极的.

In this thesis the basic aspects about forming process of camber die are studied etically.

本论文对曲面凹模成形工艺的若干问题进行了系统的理论分析.

The camber is curvature of the cross section and the crown is the highest point camber.

图中向上倾斜部分是路拱,该部分的最高点是路脊.

The measures for improving wear of camber for lockup were proposed.

针对锁紧弧面的磨损提出了改善措施.

Camber line won " ts do orthogonal arc tooth wimble gear. "

中心线 不成 直角的弧齿锥齿轮.

Application of low Mooney viscosity, non pollution type NBR to thin camber sponge rubber was studied.

研究低门尼粘度 、 非污染型丁腈橡胶在薄型曲面海绵胶料中的应用.

This provides an increased damping rate and allows a slight reduction in camber angle.

这样就增加了减震度,并且可以稍微减少外倾角.

The front subframe is modified for extra camber and castor.

前副车架被修改为额外拱形和蓖麻.

A taper has two sides, the underside is a circle, the flank is a camber.

结论:圆锥有两个面, 底面是一个圆形, 侧面是一个曲面.

The larger permeability damage modulus and the earlier the IPR curving and the camber was.

渗透率伤害系数越大,曲线弯曲越早,弯曲度越大.