A possibly good route to produce hydrogen is by gasifying cheap biomass in supercritical water.

The gasifying temperature of CNF increases by supported phosphoric oxides on CNF.

负载磷氧化物提高了CNF催化剂的适用温度,并提高了丙烯产得率.

The loading of the outboard gasket has the rule of first rose then descended.

垫片外侧载荷变化呈先升后降的规律.

Specialize in all metal gasket assembly of domestic engine.

是国内发动机全金属气缸垫总成的专业生产厂家.

Valves in these classes are also available with spiral wound gasket bonnet joints when specified.

如果用户要求,对于这些压力等级的阀门,我们也可以提供螺旋盘绕垫圈阀盖连接.

The gasket can be used for a wide temperature and pressure range.

适用于温度、压力变化范围较大的工况.

When in place, the gasket will be seated and flush with the valve body ends.

放置好后, 垫圈将与阀体连接端口一起固定和冲洗.

This form of gasket has good performance of temperature, low leakage rate, high compression spring rate.

该形式的垫片具有耐温性能好 、 泄漏率低压缩回弹率高的特点.

Lens Type: Lens gasket is shape, with metal production.

透镜式: 垫圈是透镜形状, 用金属制作.

Use sealed gasket in the water path. There isn't stress on all link surface.

水道的连接应衬有密封垫片. 所有连接面都不应有应力.

Regular testing of gasket resiliency and inspection at Receiving due to sensitivity to inconsistent quality.

由于质量差异导致灵敏性差异,因此需要经常进行密封垫弹性测试和检查接受性.

The main products are: Filter, filter, filter cover, gasket and so on.

主要生产产品有: 滤芯 、 滤清器 、 滤芯盖 、 密封垫等.

All interior surfaces exposed to piped liquid are stainless steel. Full stainless gasket surfaces.

所有与管道输送液体接触的内部表面都是不锈钢. 全不锈钢密封垫表面.

From the upper oil cap and cap gasket the oil pressure in the tank tightly inside.

油泵的上部由油箱盖和油箱盖垫片,将油泵紧紧地压在油箱内.

The compound is widely to manufacture oil seals, gasket , roller and vibration rubber products.

该产品可广泛用于油封 、 衬垫、橡胶轧辊、防振橡胶等领域.

The single piece body design has no gasket joints which eliminates potential leak paths.

阀体的设计没有接口垫片,这就消除了潜在的渗漏通道.

If you do not have a gasket, contact your supplier for a replacement.

如果你没有垫圈, 同你的供应商联系,要求一个替代品.

Metal gaskets should not be used.

不允许使用金属垫圈.

Flange, bolts, nuts, washers and gaskets not included.

不包括法兰, 螺栓, 螺母, 垫圈和衬垫.

Blind flanges and gaskets shall be chosen according to system testing pressure.

试验用的盲板法兰和盲垫应与管线试验压力相匹配.

Secure with locknut and gaskets. Install valve assembly.

用放松螺母和垫圈紧固. 安装阀门总成.