Bake in preheated oven for 8 minutes or until firm to touch and golden in color.

Having the oven preheated seems to make it easier to peel off the paper.

先预热烤箱似乎有助于揭开纸.

Lamp starting method in which lamp filaments are preheated to facilitate lamp ignition.

通过灯丝被预热使灯点燃的启动方式.

The cabinet air proofand the and exterior layer can be fully preheated by circular heating.

箱体结构封闭,采用环流加热,温度均匀,基板内外层均能受到充分预热,冲切不易分层.

The mixture is poured into the mould preheated to the same temperature.

将混合物注入已预热到同样温度的铸模内.

Bake in the preheated oven for 25 minutes.

把菠萝片轻轻铺在面糊上.

Bake for 15-20 minutes in preheated oven.

入预热的烤箱烘焙15-20分钟.

When assembling, bearing preheated and the oil temperature is less than 120 ℃.

装配时预热轴承,油温不允许超过120℃.

Bake in the preheated oven for about 12-15 minutes until lightly browned.

入预热烤箱烘焙大约12-15分钟直到浅金黄色.

Best results are obtained by using steel preheated to a tempeature of 40 ℃.

将钢材预热到40℃,可以获得最佳效果.

Hotmelts preheating to set the temperature on a sound and liquidity, it can be used.

热熔胶预热到设定温度,具有良好的流动性后, 才能使用.

Then current through C 1, RT forms the return circuit preheating filament.

于是,电流通过C1 、 Rt形成回路预热灯丝.

Kodak Carestream Health presented showcased positive plate without preheating of environmental protection plate THERMAL DIRECT plate.

柯达柯达此不主也展出了无预热侧极板技艺的环保版材THERMALDIRECT印版.

The work provides a theoretical basis for preheating or preheating treatment according to the conditions.

给出了各种情况下的应力分布,为焊接后根据使用条件是否采取消除应力措施提供了依据.

The process factors of staining salt during workpiece preheating with salt washing are analyzed.

分析了造成工件盐浴加热时沾盐问题的工艺因素.

The key of the technology was designing ideal process by using suitable preheating method.

该技术的关键是采用合理的预热方式,设计出理想的工艺流程.

Air-gas double preheating technology is adopted-beam furnace of the 750000 ton's bar steel-continuous plant in Xuangang.

宣钢75万吨全连续棒材车间加热炉所采用的是空煤气双蓄热技术.该炉热利用率较高,实际排烟小于150℃.

Organize roller before press roller has the function of preheating.

热压辊前面的整理辊可带预热功能.

A good pot preheating prior to liquid electrolyte addition if therefore considered important at most smelters.

因此,在电解液加入之前对电解槽的良好预焙是十分重要的.

Some customers require ingots for their convenience of efficient conveying and preheating of ball type ingots.

为便于运送及其预热,一些用户需要球形锭.

The preheating temperature of granules had the most prominent effect on the process of penetrating casting.

结果表明:粒子预热温度对渗流工艺的影响最显著.