He prefixed a paragraph to the book.

Class names should not be prefixed with the name of the module they are in.

类名不需要使用其所在模块的名称作为类名前缀.

She prefixed a few remarks to her speech.

她在演说之前说了几句话.

Any ASCII character can be represented as a wide character by prefixing the letter L character.

可以通过用字母L作为字符的前缀将任何ASCII字符表示为宽字符形式.

To limit the variables of ( a proposition ) by prefixing an operator such as all or some.

用量词限定通过事先设定的作用词来限制(某命题 ) 的可变性,如all ( 全部)或some(部分)

Did you clean the sand out ofthe engine and do your preflight, Mr. Towns?

你清理了发动机里的沙子并作好起飞前的准备了么, 唐斯先生?

Truck fractures most often occur at maximum loads as after fueling or during preflight taxi.

支柱的断裂大多出现在最大载荷的时候诸如飞机后部加油时或在起飞前的滑跑过程中.

An algorithm of three-dimensional braided composite material preform image processing based on mathematics morphology is presented.

提出一种基于小尺度的数学形态学的三维编织复合材料预制件图像的边缘检测方法.

Transverse feeding of molten metal in continuous fiber preform was investigated theoretically and experimentally.

研究了金属液在连续纤维预制型中的横向补缩.

A preform shape can be gained with backward simulation from the final bladeshape based on FEM.

为此,本文介绍了有限元反向模拟的基本步骤,综述了确定反向模拟中边界节点脱模准则的方法.

AZ 91 magnesium preform with complete shape prepared using spray forming technology under protective atmosphere.

在保护气氛中采用喷射成形制备技术制备了形状完整的AZ91镁合金沉积圆柱坯.

An 8-cavity preform mould costs more than the injection moulding machine that holds it.

八腔以上的模具价钱比注塑机还要高.

But they also reported that not all green roofs preform perform equally well.

但是他们也报告了不是所有的绿色屋顶都做得同样的好.

Bottle weight , which is the same as preform weight, is essentially non-adjustable.

瓶子的重量(壁厚)相当于瓶坯的重量, 而后者基本上不能调整.

Knowledge on plastic material and quality control on preform manufacturing.

具备塑料和瓶胚生产品控的知识.

In the injection stretch blow moulding process, injection moulding machine is used to make the preform.

注拉吹工艺先用注塑机注出瓶坯.

Major in PET preform mould, cap mould and blow mould.

专业生产瓶坯模具, 瓶盖模具和吹瓶模具.

Precise preform loading system in order to minimize failure rate.

高可靠性的进坯、上坯、出坯系统、使吹瓶机故障率降到最低.

This paper studies the production process of one mould of preformed strain clamp.

本文探讨了一种预绞式拉线耐张线夹模具的加工工艺.

Please advise the test requirement and describe how the test to be preformed.

请提供测试要求,并说明如何将预制测试.

This is also preformed on covered surfaces a stacked assembly : substrate-pre-form-die.

在叠层的组装工艺中,比如基板 - 焊片 - 芯片,即使有部分表面被盖住了,这种气氛同样有效.