Family of confocal centred conics According to the restriction of the generatrix line, Bertrand surface can be constructed with the Bertrand curve with broad sense group.

Conical shaft extension for rotating electrical machines conical drum reversing concrete mixer

GB/T757-1993旋转电机圆锥形轴伸锥形反转出料混凝土搅拌机

Conical drum reversing concrete mixer

锥形反转出料混凝土搅拌机

The check valve of the single piston pump was replaced by ball valve, and conical valve with guidance was used for safety valve;

单柱塞油泵的单向阀改成球阀，安全阀改用带导向的锥阀；

Axial Force of Conical Valve

圆锥阀的轴向力

On Waveguide Band-Pass Filter Axial Force of Conical Valve

波导带通滤波器圆锥阀的轴向力

Through examples in practice, the paper presents the fault diagnosis and treatment of conical valve system.

以实例说明了锥阀系统故障的诊断与处理方法。

Fault diagnosis and treatment of integrated conical valve hydraulic system

锥阀集成液压系统的故障诊断与处理

A New Model and Simulation of the Movement of Self-acting Conical Valve of Reciprocating Pumps

往复泵自动锥形阀运动规律的新模型与仿真

It also approach theoretically to change the conical valve gag into globe valve gag to raise the stability of the seal plate.

并在理论上探讨将锥形阀瓣改为球形阀瓣，提高密封面的稳定性。

Experimental Investigation on Conical Horn Excited by an Azimuthally Symmetric Mode with Plate Lens

轴对称模激励的加平行板透镜圆锥喇叭实验研究

Mode-Matching Analysis of the Reflection Characteristics for Conical Horn Antennas with Small Flaring Angle

小张角圆锥喇叭天线反射特性的模匹配法分析

Dielectric resonators and a conical horn antenna were calculated by the presented methods.

采用提出的方法计算了介质谐振器和圆锥喇叭天线。

A Multimode Conical Horn of Simple Structure in 4MM Wave Band

一种结构简单的4mm多模圆锥喇叭

Design of dual-mode conical horn feed with equal E and H patterns

E面和H面方向图等化的双模圆锥喇叭设计

Calculation of Fields Radiated from Conical Horn by Using Mode-Matching Method

模式匹配法计算圆锥喇叭的辐射场

Analysis of Near Field Radiation Behaviour in a corrugated Conical Horn

波纹圆锥喇叭近场辐射特性分析

Analysis of errors in optimization of conical hydrostatic bearing for minimum friction

锥形液体静压轴承优化设计中的误差分析

A study on the CAD system for the conical hybrid bearing

圆锥动静压轴承CAD系统研究

By analyzing constitution of the preset clearance of transmission conical bearing and its measuring method, it is pointed out that there exist angular errors for measuring results of the conventional measuring method due to operating force of measuring, and there is no enough review of measuring results.

通过对变速器圆锥滚子轴承预留间隙的构成以及测量方法的分析，指出通用的测量方法存在着由于测量力的作用导致测量结果出现角度偏差及缺乏对实测结果校核的问题。

Study of Dual Conical Bearing and Its Application in Hydro-Electrical Servo Actuator Buckling capacity optimization of cylindrical shell with rectangle stiffeners under uniform axial compression

双圆锥静压支承应用在电液伺服作动器中的研究矩形加筋圆柱壳轴压屈曲承载力优化