Put on chain between crankshaft drive sprocket and intermediate shaft drive sprocket.

This paper introduces the principle and method of the holding control for automatic charging and plunger chip, which is realized by using proximity switch to test the motion of crankshaft of punch press, and velay or SCR to control clutch through electromagnet.

本文介绍了利用接近开关检测冲床曲轴动作，利用继电器和可控硅通过电磁铁控制离合器吸合动作，从而实现冲床自动送料动作和冲头动作同步控制的原理及方法。

Equilibrium analysis on crankshaft's rotation inertia force of internal combustion engines

内燃机旋转惯性力的平衡分析

The second injection pump drive and installation, the secord injector arrangement, the cylinder head and rocker arm support modifications are described in detail, as well as the installation of crankshaft rotation angle grating disc which is necessity for combustion research in cylinder pressure sensor.

详细论述了喷油泵的安装和驱动、喷油器的布置、气缸盖和摇臂座的改造以及气缸压力传感器、曲轴转角信号光栅盘轴的安装。

The conclusion from the analysis points out that the effective way to raise the productivity of this series of looms, while maintaining the same shuttle speed and low power consumption, is to increase the angle of crankshaft rotation available for the passage of the shuttle.

文章从分析得出结论：从既提高生产率，又维持棱速不变，并保持较低的功率消耗来看，唯一有效的措施是进一步扩大梭子越过梭道的时间角度。

The output for diesel engine is proportional to the product of crankshaft rotation speed and injection pump rack displacement from fuel supply starting point. Injection pump rack displacement influences diesel engine rotation stability and locomotive tractive characteristic.

柴油机输出功率的大小跟曲轴转速与喷油泵齿条由供油始点开始的位移量乘积成正比，喷油泵齿条位移量影响柴油机运转的稳定性和机车的牵引特性。

Counter crankshaft rotation The steering wheel is mounted on a steering shaft that extends into the steering gear.

反曲轴转动方向的转动转向盘安装在转向轴上，转向轴延伸至转向器。

The boat began to move slowly off toward the northwest. counter crankshaft rotation

船儿慢慢地向西北方向驶去。反曲轴转动方向的转动

Engine crankshaft front, rear oil seal on the sealing function of crankshaft rotation, which guarantees good lubrication of the engine cylinder body, reduce friction power loss.

发动机依靠曲轴前、后油封实现对曲轴旋转运动的密封功能，保证了发动机缸体内有良好的润滑，减低摩擦产生的功率损耗。

Optimize on Working Parameters Crank Rolling Velocity and Radius of the Vibration Sieve about Cereal Cleaning Windmill

谷物清选风车中振动筛的曲柄转速和半径优选

Influence of Crank Radius of E7/ 6 Type Comber on Its Process Performance

E7/6型精梳机曲柄半径对工艺性能的影响

No, you just crank up the handle to power it up.

不用你只需摇手柄就能启动

The crank handle is rotated to lead a screw to rotate through an umbrella wheel.

转动摇把，通过伞轮使螺杆转动。

Dynamic stability analysis of a slider-crank mechanism with elastic effects

具有弹性效应的曲柄滑块机构的动态稳定性研究

Design the Slide Crank Mechanism According to the Optimum Transmission

按传动最有利条件设计曲柄滑块机构

Optimal Design of Planar Slide Crank Mechanism with Transmission Force Property

平面曲柄滑块机构传力性能优化设计

Crank mechanism design provides strong pressure with little loss;

曲肘机构设计，压缩空气消耗少，压力强劲。

Calculation formulas are established based on the functions of given movement and dynamical conditions by means of extremum theory, making analytical design of an offset slider crank mechanism more convenient and good for extend.

本文根据偏置曲柄滑块机构的运动特性和传力特性所建立的函数关系，运用极值理论推导出给定条件下传力特性最佳的计算公式，大大方便了设计应用，值得推广。

Because the trough movement is a standard crank mechanism, the movement equation on the displacement ( s), speed ( v), acceleration ( a) and time ( t) was established.

往复槽锅为一典型的对心曲柄滑块机构，写出了位移S、速度V和加速度a与时间t的运动方程。

This paper describes the distribution of surface hardened layer and analyses of the residual stress in the nodular graphite cast iron crank shaft with its Journal and arm corner hardened simultaneously by high frequency induction heating.

本文叙述了对球墨铸铁曲轴轴颈与园角部位同时高频淬火后获得的硬化层分布，以及硬化层中残余应力分析。

The fillets of crank pin and main journal have a relatively weak strength. In establishing the grid model for crankshaft, these fillets need to be refined.

曲柄销与主轴颈的圆角为强度较薄弱部位，在建立曲轴网格模型时，需要对这些圆角处进行细化。