Test for separating oil-water fluid with high oil content by hydraulic cyclone

Simulation analysis and structural optimization for a liquid-liquid hydraulic cyclone

液-液水力旋流器的模拟分析与结构优化

According to the distributions of the flow fields in the cyclone air classifier with a fixed spherical wall, the formulas of the classification and collection cut sizes are presented and they are examined by experiment.

根据球台固定壁旋流式气力分级机内的流场分布，推导出了分级粒径和收集粒径的理论计算公式，并通过实验对计算公式进行了验证。

A new type of hydrostatic bearing influence of the static pressure gradient in cyclone air classifier on the test for its flow fields by five-hole probe

静压梯度对五孔探针测试旋流式气力分级机流场时的影响

The static pressure gradient in cyclone air classifier can have influence on the test and measurement for its flow fields by five-hole probe.

用五孔探针测试旋流式气力分级机流场时，分级机内存在的静压梯度会对测试产生影响。

In this paper, the flow fields in the cyclone air classifier with a fixed spherical wall are explored and their characteristics are found.

本文对自行设计的球台固定壁旋流式气力分级机模型进行了研究，对它内部的流场进行了测试，找出了流场的分布规律。

Today's rock powder processing gives out serious particle pollution, which is resulted from low collection efficiency of cyclone classifier.

现有的石粉加工技术存在大量排放粉尘的问题，问题的症结在于旋风分级器收集效率不高。

The newly developed super fine cyclone classifier is used to test for the cement classification.

用新开发的新型旋风式微细分级机进行水泥微细分级试验。

Study to the Experiment for the Separation Size in the Turbo Cyclone Classifier

涡轮式气流分级机分级粒径的试验研究

Based on the analysis of the working principle of arc-cycloidal gear pump and the motion relationships parametric equation of a kind of cycloidal curve ot internal tooth was put forward, the trouble of processing and mapping when the rear damaged was solved.

对圆弧-摆线齿廓转子泵工作原理及运动关系进行分析的基础上.提出一种内转子摆线齿廓曲线的参数方程，解决了内转子加工以及损坏后难于测绘的难题。

A Cam Profile-Combined-Cycloidal curve used for high speed Automobile Engine intake and exhaust valves is proposed.

本文提出一种高速车用柴油机配气凸轮的型线&复合摆线凸轮轮廓。

Using this formula to estimate the performance of the cycloidal propeller and comparing the computational results with experimental results, it is shown that the agreement between them is quite good.

本文还指出，该公式的形式也适用于其它的摆线推进器，但是公式中的各项系数应根据不同的推进器而取相应的值。

Calculation of common normal length of inner rotors in cycloidal pump

摆线泵内转子公法线长度的计算和测量

Optimization Design of Basic Parameter in Cycloidal Pump

摆线泵基本参数的优化设计

Research on the novel three-tipped cycloidal pump and its structure

新型三尖摆线泵及其结构研究

Optimization of the Design Parameters of Cycloidal Pump with Singularity Type Profile

异型齿廓摆线泵的参数优化设计

Discussion on Design of Cycloidal Pump with Multi-tooth Number Difference

多齿差摆线齿轮泵设计计算探讨

Study on the meshing characteristic of a new cycloidal pump

新型摆线转子泵啮合特性的研究

Analysis and Simulation of Flow Characteristics of Cycloidal Pump

摆线泵流量特性分析及计算机仿真

Based on the theory of forming cycloidal gear, this paper discusses the basic fundamentals and methods of machining cycloidal gear with cam mechanism.

根据摆线齿轮齿廓的形成理论，探讨利用凸轮机构实现摆线齿轮加工的原理和方法。

Development and Application of Subprogram of SIEMENS CNC System for Cycloidal Cam

SIEMENS数控系统摆线凸轮加工子程序的开发与应用