Coil binding is one of common half man-made binding methods and its products are completely spread out and placed.

The supporting system of a big board and the binding bolt are used to strictly control the construction technology so that the problems mentioned above are basically solved.

本文采用大板支撑体系及对拉螺栓加固等方法，并严格控制施工工艺，基本消除了胀模、烂根等质量问题。

The measurement of binding bolt axial force is always a task of the steelwork connection in the construction of bridge and high-rise buildings.

紧固螺栓轴力检测是桥梁与高层建筑中钢结构连接施工所经常面对的任务。

The Reliability Design of Binding Bolt in Turnplate Bearing

转盘轴承中连接螺栓的可靠性设计

Research on the Echoing Analysis Technique for Measuring The Axial Force of Binding Bolt

回声法紧固螺栓轴力检测技术研究

Some riders put a dab of nail polish on the binding's screw threads to help keep the screws in place.

有一些滑雪者会往固定器的螺丝上涂上指甲油保证螺丝不会松动。

Application on the Process of Over Quenching Medium 40 Cr Steel Binding Screw

40Cr钢紧固螺钉整体淬火介质的应用

It is effective to control the overwinter larvae by binding grass ring and smearing poison lime, and spraying B.T turbid liquid.

越冬幼虫的防治以绑草环诱杀和涂毒灰熏杀及喷白僵菌悬液防治较为有效。

In this paper, the end binding ring of generator rotor is designed and the primary prestress effect is analyzed under the limitation of the maxium space size. And the special binding ring manufacturing technology is also presented and implemented.

在空间尺寸极大限制条件下，对发电机转子绕组端部绑扎环进行了设计并进行了初步的预应力效果分析，提出并实施了特殊绑扎环制造技术。

Reaction mechanism of the mixtures is tried to change by entering metal powder and metal oxides, organic matter that contains much carbon and special binders into the mixtures in order to produce more substances of infrared extinction and arrive at the aim of infrared extinction.

通过向赤磷发烟剂中加入金属粉和金属氧化物，富碳有机物和特殊的粘合剂，试图改变赤磷发烟剂的燃烧反应机理，使之生成更多的红外消光物质，达到红外消光的目的。

The wear mechanism of original WC-Ni cemented carbide during the wear process is abrasive wear with the main characteristics of plastic deformation of Ni binder phase and fall-out of WC grains, and wear resistance depends on the hardness of cemented carbide.

原始WC-Ni硬质合金的磨损以Ni粘结相的塑性变形和WC晶粒脱落为主要特征的磨粒磨损，耐磨性依赖于硬质合金的硬度。

The erosion mechanism at 90 degrees includes block exfoliation, the plastic deformation of binder phase and the extrusion of the carbides, meanwhile, the brittle fracture character has also been observed with a speed of 420 meters per second.

90°冲蚀机制包括块状剥落，粘结相的塑性变形和碳化物的挤出，420m/s冲蚀的粘结相还表现出了脆性断裂的特点，块状剥落是质量磨损率升高的主因。

Due to the existence of surface tension, plastic film was binder together and so difficult to separate when it was compressed or heated in accumulation and bound volumes.

塑料薄膜在堆积及缠卷时，由于表面张力的存在，当受压或受热时，容易使塑料薄膜黏结在一起，不易分离，甚至无法使用。

The principle and characteristics of magnet injection molding are explained and its key technologies are analysed from magnetic particulate, plastic binder and mold, process.

并且在磁性颗粒塑料粘结剂、模具、工艺等方面分析了该工艺的关键技术。

Study on the New Producing Technique and Curing Mechanism of CO_2-Cured Phenolic Resin Binder

新型CO2硬化酚醛树脂粘结剂制备技术及硬化机理的研究

Study of synthesizing phenolic resin binder by two-step technology

二步法合成酚醛树脂结合剂的研究

Study on New Thermosetting Inorganic Resin Binder for Moulds and Cores

一种新的环保型热硬化无机高聚物铸造粘结剂研究

Research on Component and Cure Mechanism of CO_2 Cure Phenolic Resin Binder

CO2固化碱性酚醛树脂粘结剂的组成及固化机理研究

Preparation of a higher strength phenolic resin binder for casting

一种高强度铸造酚醛树脂的研制

The paper introduces good quality and multiple-use complex epoxy resin binder and its application in anti-corrosion coating of chemical storage tanks.

本文主要阐述了性能优良、应用广泛的复合型环氧树脂粘合剂，在化工贮罐、防腐涂层的工艺和方法。

The survey and analysis show that when the rut depth is deeper ( more than 60 mm), the greater deformation would be found both in wearing course and binder course, and the compression deformation ratio of binder course is higher than that of wearing course.

测量分析结果表明，车辙深度较深（大于60mm）时，上、下面层均发生了较大的变形，且下面层的压缩变形率大于上面层；