Study on the Vision Detection System of Automatic IC Wire Bonder

Software Analysis and Design of the Fully Automatic Gold Wire Bonder

全自动引线键合机系统软件分析与设计

Simulation Analysis and Experimental Study of Wire Bonder Precision Positioning Table

键合机精密工作台仿真分析与实验研究

Analysis of Some Factors Improving Performance of Ultrasonic System in Wire Bonder

提高引线键合机超声系统性能的若干因素的分析

Due to the particular mechanical performance and good applicable feature, the bonded rubber block has been widely applied in engineering practice.

粘合的橡胶块体由于其特有的力学特性而被广泛应用于工程中的受载元件。

The results of in-situ measurement of the deflection of bonded prestressed concrete roof beams with a span of 21 meters in frame structure of a gymnasium after construction are presented.

某健身房跨度为21m的有粘结预应力屋面框架梁，在竣工后对其进行了挠度的实测。

Discussion on Bonded Prestressed Roof Design and Construction Technology of High-rise Building Basement

高层建筑地下室有粘结预应力顶板设计与施工技术探讨

Bonded goods: Taxable goods held in a government-licensed warehouse pending payment of customs duties and other taxes due.

保税货物：在交纳关税和其他应付税之前，存放在政府特许的仓库内的应税货物。

If, upon approval, the bonded goods are not to be shipped out of China;

保税货物经批准不复运出境的；

Bonded Goods: Goods under bonded storage without import procedure, and import duty unpaid;

保税货品：指在保税仓储状态下尚未完税的货品；

Research on Financial Logistics Business Mode of Bonded Goods

保税货物开展金融物流业务模式研究

The results showed that the aging of epoxy bonded joint in water was accelerated by increasing temperature.

结果表明，提高温度可以加速环氧胶接接头在水中的老化；

Effect of Alkaline Anodization Treatment of Durability of Titanium/ Epoxy Bonded Joint

碱性阳极化处理对钛合金／环氧胶接接头耐久性的影响

Effect of process parameters and interlayer on properties of 1420 Al-Li alloy diffusion bonded joint

1420铝锂合金扩散焊工艺及中间层材料对接头性能的影响

Damage to the bonded joint if the waiting time is not observed before further work!

如不遵守等待时间而急于展开下一步工作，粘合处将受损！

Review on residual thermal stress of ceramic bonded joint with metal

陶瓷与金属焊接接头残余热应力研究

In this study, effect of cyclic load on the vacuum tightness of the adhesively bonded joint was investigated experimentally.

该文实验研究了循环载荷对粘接接头气密性的影响。

The Influence of Preparation Processes on Fretting Wear Life of MoS_2 Bonded Solid Lubricating Coating

制备工艺对MoS2粘结固体润滑涂层微动磨损寿命的影响

Study on Curing Process of Fusion Bonded Epoxy Powder Coating ( FBE) of Pipe

管道熔结环氧粉末涂料固化工艺的研究

Fusion bonded epoxy coating as a member of high performance coating family has been widely used for corrosion protection of steel pipeline and pipe pile.

熔融结合环氧粉末涂层的综合防护性能优良，已经大量应用于钢质管道和钢管桩，也很适合于钢筋的保护。钢筋表面涂装环氧涂层可用静电喷涂方法，工艺基本成熟。

The EIS results of bonded coating indicate that three time constants were obtained during the initial immersion period, and then a new time constant appeared due to the formation of rust layer.

而对于有粘结层的涂层，其交流阻抗谱在浸泡初期具有3个时间常数，浸泡后期由于在碳钢表面生成了一层腐蚀产物，出现了1个新的时间常数。