Large quantity of rejected products involving edge crack and strip breakage are prone to occur in hot and cold rolling of the oriented silicon steel sheets due to high brittleness of the steel caused by its high silicon content.

Strip breakage and roll wind-up frequently occur on the ZR 20 when rolling the fragile stock with severe quality problems such as worse shape, serious surface and edge defects.

森吉米尔轧机（ZR20）在轧制板形不好、板面和边部有严重缺陷的脆性原料时，经常出现的生产故障是断带缠辊。

Strip breakage happened very often in the annealing assembly line at the silicon steel workshop of Wuhan Iron& Steel Corp.

武钢硅钢厂退火生产线经常发生因带钢跑偏造成断带事故。

Study on Strip Breakage Inside Furnace of Continuous Annealing Line of Cold Rolled Sheet

冷轧薄板连续退火线炉内断带原因分析

Measurement and analysis on strip breakage and roll wind-up on ZR mill

ZR轧机断带缠辊的测试及研究

However, when the content of Si is about 10%, its plasticity is poor, particularly in cold-rolling process. The poor plasticity led to the strip breakage in rolling process and it reduced the rate of finished products.

然而，4004Al-Si合金，由于含Si量在10%左右，塑性差，特别是冷轧性能差，进而导致轧制过程中易产生断带，成品率低。

The cause for roll collar breakage and countermeasures as well as the effect after implementing at Bar and Wire Rood Plant were analyzed.

分析我厂造成高速线材轧机辊环碎辊的原因，提出改进措施以及实施后的效果。

Causes to roll breakage of two high rolling mill in plate mill and preventative measures

轧板厂二辊轧机断辊原因及防范措施

An Analysis of Work Roll Breakage of Tandem Mill

武钢冷轧厂五机架工作辊断裂原因分析及改进措施

Resolution the steel rolling problem of roll breakage with heat ageing method

用热时效法解决轧钢的断辊问题

The roll breakage status and its causes in the First Bar Production Line in last two years have been introduced, and the countermeasures for reducing the roll breakage have been put forward.

分析了棒线厂一棒生产线近两年来发生的断辊情况及原因，并提出了减少断辊所采取的有效措施。

On-line Monitoring of Cutting Tool Breakage in Milling Operation Based on Cutting Force

基于切削力的铣刀破损实时监测技术研究

Study on The In-process Monitoring and System for Tool Breakage

刀具破损在线监测及其系统的研究

Tool Breakage Monitoring System in Automatic Process

自动化加工刀具破损监测系统

At last, the equation of tool breakage model is achieved.

并应用这种方法得出刀具破损模型的方程。方程的确定为刀具破损状态的预报监控奠定了基础。

The On-line Monitoring System Of NC Tool Breakage Using Wavelet Analysis

基于小波分析的数控刀具状态在线监控系统

Investigation on a New Alarm System for Cutting Tool Breakage

一种新的监控刀具破损报警系统的研究

The On-line Monitoring System of Tool Breakage in Numerical Control Cutting

数控切削过程中的刀具破损在线监控

Fiber breakage and its development in fiber reinforced composites

单向纤维增强复合材料中纤维断裂及其发展

The intensifying of carding action often accompanies the increasing of fiber breakage.

加强梳理作用常会引起纤维断裂。

Stress concentrations in a composite sheet due to fiber breakage

复合材料内由纤维断裂引起的应力集中