bolts的例句大全

The door bolts on the inside.

这扇门要从里面锁.

The oil pan bolts under engine block, where It'seals off the bottom of engine.

该油底壳螺栓下,发动机缸体, 而海豹小康底部的引擎.

Loosen oil pan bolts and remove the front bolt at each side.

松动油底壳螺栓,拆下每一面的前螺栓.

Electric nut runner: used to tight large quantity of small bolts with presetting torque.

电动扭矩扳手: 解决大量的小螺栓定扭紧固要求.

A figure is made to show the relationship between preload and fatigue limit of bolts.

为了研究预紧力对螺栓疲劳极限的影响,实验求得了螺栓的疲劳图.

The nameplates are fixed on the equipment by antirust machine bolts or other acceptable methods.

3利用防锈机器螺钉或者其他可接受的方法将铭牌固定在设备上.

Rig tong pins, shackle pins and bolts must be secured with the proper size split pins.

大钳销子,卸扣的销子和螺栓必须配有合适尺寸的开口销.

Gland Eye Bolts: Eyebolts swing aside for ease in repacking the stuffing box.

压盖有眼螺栓: 有眼螺栓可以从旁边旋起,使得填料函的填料更换更加容易.

Measuring dimension of shaft coupling bolts and reamer hole.

轴系连接螺栓和钻孔尺寸测量.

The four screw bolts should be tightened up in turn in a symmetrically diagonal position.

四只螺栓要对称地成斜对角形式依次收紧.

Bolts must be stainless steel or titanium.

1锚栓必须为不袗或钛金属.

Turn the shaft, if the clutch-disk hub splines. Put Bolts in place , and tighten correct tension.

如果与离合器 从动 盘轮彀的花键相连,可转动传动轴, 把螺栓就位, 并适度拧紧.

Specializing in the production of high-strength bolts fastening nut.

专业生产高强度紧固件螺栓螺母.

The bolts holding the wheel in place sheared off.

固定这个轮子的几个螺栓断了。

Bolts with drilled or undersize heads shall not be used.

被钻孔或头部尺寸太小的螺栓不能使用.

Pull back the wheelhouse liner and remove the bolts attaching the end cap the front fender.

拉下舵手室外套,拆去连接末端端盖到前挡泥板的螺栓.

The machines start to wear down, they don't make as many nuts and bolts as they used to...

机器开始出现磨损，螺母和螺钉的产量不如从前了。

Install in valve using existing valve Bolts, Nuts, Washers and Handle Nut.

采用现存的阀门螺栓 、 螺母 、 垫圈和手柄螺母安装在阀门内.

Stainless steel stuffing box hardware is standard ( ie. bolts, gland studs, nuts, washers ).

标准的金属密封不锈钢填料箱 ( 如螺栓 、 填料压盖螺栓 、 螺母 、 垫圈 ).

The tie-rod ends have left-handed or right-handed thread and are locked with coupling bolts.

该拉杆两端有左手或右手线程,并锁定与耦合螺栓.