camshaft的例句大全

Remove camshaft sprocket and chain tensioner.

拆下凸轮轴链轮和链条张紧器。

If one of the camshafts cannot be locked, loosen all the fastening screws on the affected camshaft sprocket by about one turn.

如果有一根凸轮轴无法锁定，则松开相应凸轮轴链轮上的所有紧固螺钉（旋转一圈左右）。

Comparative study show that the drive system using the nonstandard sprocket is improved in many ways such as chain tension, contact force and friction force between chain and transmission components, tension force provided by tensioner, angular velocity of camshaft sprocket.

通过对比研究，采用非标准链轮的传动系统，其链条的张力、链条与传动部件之间的接触力和摩擦力以及张紧器的张紧力都有明显的改善。

The new technology and new structure of model AJR engine applied in Santana 2000 car is introduced, including light valve gear, camshaft, tappet friction pair, timing transmission system, lubricating system and cooling system.

对桑塔纳2000轿车用AJR发动机从以下几个方面：轻型气门机构、凸轮轴和挺杆摩擦副、正时传动系统、润滑系统和冷却系统的新技术、新结构作了概要分析。

A control system for the intake camshaft to vary the opening and closing times in combination with a valve lift system is necessary.

用于改变开放和关闭时间的进气凸轮轴控制系统和气门升程系统是必备的。

The camshaft also fits inside the block , except on overhead-cam engines ( OHC ).

除了顶置凸轮 ( OHC ) 发动机以外,凸轮轴都安装在气缸体里面.

Research into the Underslung Valve Mechanism of CG Motorcycle Engine Camshaft

摩托车CG发动机凸轮轴下置式配气机构的研究

Remove camshaft housing removing and installing camshaft housing.

拆下凸轮轴室拆卸和安装凸轮轴室。

Install the camshaft housing cover on both cylinder banks installing cover for camshaft housing.

安装两个气缸组上的凸轮轴室盖安装凸轮轴室盖。

Development of Intelligent CNC Camshaft Grinding Machine Control Software and Research on the Camshaft Grinding Experiments

智能凸轮轴磨床控制软件编制和加工试验研究

Machining precision of camshaft with domestic automated NC camshaft grinding machine is far from satisfaction, so imported equipments are applied to the manufacture of camshafts, but it leads to a high cost.

我国全自动数控凸轮轴磨床加工的凸轮轴精度往往达不到要求，故凸轮轴的加工主要依靠进口设备，但进口设备售价相当昂贵。

Describes the math model of grinding camshaft, the mechanical structure of the CNC camshaft grinding machine ourselves and the experiment, then discusses the machining technics.

介绍凸轮轮廓磨削加工的数学模型及研制的数控凸轮轴磨床的机械结构，进行加工实验并讨论凸轮轴磨削的工艺参数。

If chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets.

若正时链不令人满意，则拆下凸轮轴链轮固定螺栓，并拆下曲轴和凸轮轴链轮的正时链。

In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.

在发动机里, 机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上.

For-line 4-cylinder engine using dual-overhead camshaft DOHC structure set CVTC ( continuously variable valve timing control ) technology.

发动机为直列4缸,采用DOHC双顶置凸轮轴结构集合CVTC ( 连续可变气门正时控制 ) 技术.

As the camshaft continues to rotate, the high spot moves way from the valve mechanism.

因为凸轮轴继续旋转, 凸轮轴上的凸起部分离开气门装置.

OCV is the oil control valve of VVT engine, which determines when the intake valve open and close. The main purpose of actuator is to change the camshaft phase.

OCV是可变气门正时发动机上控制发动机的进气门正时的机油控制阀，执行器是改变凸轮轴相位的控制器。

The Approach of the Angle Measure on Gears over the Camshaft and Crankshaft

凸轮轴齿轮和曲轴齿轮正时角度检测新方法

These help the fitter during initial assembly in the workshop and must match the corresponding markings on the sprockets and camshaft adjusters.

这些链节会在车间的初始装配期间对修理工人起帮助作用，并且必须与链轮和凸轮轴调整器上的相应标记匹配。

Design of the NC Special Milling Machine for Brake Camshaft

制动凸轮轴数控专用铣床设计