composites的例句大全

In situ titanium alloy matrix composites were fabricated by melting casting.

用熔铸法制备了原位自生钛合金基复合材料.

Finally, some simple opinions on further development of cyclic fatigue in ceramic matrix composites are presented.

最后, 还对进一步研究陶瓷基复合材料的循环疲劳特性提出了一些粗浅的看法.

Study of dynamic mechanical behavior of cpe/ dz/ vgcf Composites

CPE/DZ/VGCF复合材料动态粘弹性研究

Particle-dispersed is a mostly-used method to fabricate ceramic composites.

颗粒弥散增强复相陶瓷是经常使用的材料复合方法.

Carbon/ Carbon ( C/ C) composites are regarded as the most promising heat-resistant materials for long-playing structures at ultra-high temperature and have important strategic value to the national defense.

碳/碳（C/C）复合材料被认为是最有发展前景的超高温长时间使用的热结构材料，具有重要的国防战略价值。

A forming process for preparing high density crystalline ceramic matrix composites was suggested.

为制备高致密度晶态陶瓷基体复合材料推荐了一种成型工艺和一种制备过程.

Current status and outlook of in situ discontinuously reinforced titanium matrix composites

原位自生非连续增强钛基复合材料的研究现状与展望

Research Progress on Non-Conducting Polymer/ Carbon Nanotubes Functional Composites

非导电聚合物/碳纳米管功能复合材料研究进展

This isothermal crystallization kinetics of PP/ talc composites was treated using Avrami equation and the effect of talc on the crystallization activation energy was treated using Kissinger equation.

用Avrami方程全面分析PP/滑石粉的等温结晶动力学，并由此获得相关的动力学参数；用Kissinger方程研究滑石粉对PP/滑石粉复合材料结晶活化能的影响。

Preparation of Micron Polymer-Fe Capsulized Composites by Mechanic Milling and MR Effect of Concentrated Suspensions

微米级高聚物包埋型金属铁复合粒子的球磨法制备及其磁流变效应

C/ C composites with density as high as 1.74 g/ cm 3 were obtained within 3 hours by the new process. Carbon felt disk preforms have been densified in a liquid carbon source. The liquid precursors studied in the present work include CYH and KEE.

利用该技术，采用碳毡作预制体，以两种液态低分子有机物作碳源前驱体，沉积时间在3h内，沉积温度在900℃～1100℃范围内可获得密度达1.74g/cm3的C/C材料。

A study on pp/ poe/ talc Ternary Composites

PP/POE/滑石粉三元复合材料的研究

Based on conventional manufacture methods a new manufacturing process of foam sandwich structure composites is studied.

在传统泡沫夹层结构复合材料成型工艺基础上,探索了一种新型的夹层结构成型工艺.

Studies on synthesis and application of molecular sieve composites were also noticed.

还介绍了具有应用前景的复合分子筛的合成和应用的研究结果.

Study on Performance of Alkali-activated Waste Residue Composites ( AAW) Concrete

碱激发复合渣体（AAW）混凝土的性能研究

Advanced technical ceramics-Ceramic composites-Thermophysical properties-Part 1: determination of thermal expansion.

高级工业陶瓷.陶瓷复合材料.热物理性能.第1部分: 热膨胀的测定.

Besides, the effect of diffusion coefficient on interlaminar shear stength of composites is investigated.

此外, 还研究了扩散系数对芳纶纤维复合材料的层间剪切强度的影响.

With increase of infiltration temperature, the amount of CrW solute increases, which leads to the increase in hardness and breakdown voltage, but the decrease of electrical conductivity and chopping current on the condition of the same Cr content in the CrW/ Cu composites.

CrW/Cu复合材料中，对Cr含量相同的配比，随着熔渗温度的升高，基体中CrW固溶体增多，材料的硬度、耐电压强度升高，电导率、截流水平则降低。

Therefore, the surface treatment of hBN becomes the key point in the preparation and application of high performance hBN/ polymer composites.

因此六方氮化硼的表面处理成为高性能六方氮化硼/聚合物基复合材料的制备与应用的关键。

Effect of hBN and Calcined Petroleum Coke on Friction and Wear Properties of Phenolic Resin-based Friction Composites

煅烧石油焦及六方氮化硼对摩阻材料摩擦磨损性能的影响