composites的例句大全

Research and development of ablative performance of C/ C composites

C/C复合材料烧蚀性能的研究进展

Study on factors affecting ablative performance of c/ c Composites

炭/炭复合材料烧蚀性能影响因素分析

Research on the influence of short fiber brucite on the performance of cement based composites

水镁石短纤维对水泥基复合材料强度影响的研究

But fiber volume fraction are raised via elevating molding pressure, when the molding pressure are too high the fibers will be damaged seriously, the composites will become brittler and show poor mechanical properties as a result.

但是纤维体积分数的增加要通过提高模压压力来实现，当模压压力过大时，纤维出现机械损伤，复合材料变脆、力学性能降低。

Parametric studies show that the axial elastic modulus of the composites increases with increasing the linear density ratio of axial yarn to braider yarns and pitch length.

参数分析结果表明，轴向弹性模量随轴纱与编织纱线密度之比和节距长度的增加呈增加趋势。

Application of medical CT in internal quality evaluation of braided fabric reinforcement for composites

医用CT在编织复合材料织物增强体内部质量评价上的应用

But, they do have several obvious advantages over the other fiber performs such as woven and braided fabric reinforced composites, including mass productivity, low fabrication cost, superior resistance to impact, and high ability to conform to complicated contours.

但是，相对于编织物和机织物等一些其他类型的增强复合材料，经编针织复合材料的优势也非常明显，如生产率高，成本低，耐冲击，适应复杂形状的能力等。

Influence of Twist of Nylon Bundle on Bonding in Cement Composites

尼龙束捻度对水泥砂浆界面粘结的影响

Interface structure, constituent phase and the forming mechanism of the composites were investigated systemically.

系统分析了复合材料界面结构 、 组成相及其形成机理.

Carbon fiber and carbon fiber composites are widely used in stealth technology.

炭纤维和炭纤维复合材料在隐身技术中已经得到了广泛应用.

The heat properties of the composite were studied by DMA and TGA. The results showed that when the content of CNTs was less than 1.0%, the glassy transition temperature of the composites lower than that of PMMA and the decomposition point had no evidently change;

DMA和TGA的研究表明，碳纳米管用量少于10%的复合物玻璃化温度降低，分解温度无显著变化。

Effect of properties of epoxy resins on compression failure characteristics of composites

环氧树脂性能对复合材料压缩破坏特征的影响

Compression Failure Behavior of 3 D C/ SiC Composites

3DC/SiC复合材料压缩失效规律研究

After C/ C composites were treated under 2500 ℃, they had smooth brake process and small wear, and their average dynamic FC was slowly decreased in damp condition.

经过2500℃处理的C／C材料，不仅刹车过程平稳，湿态平均动摩擦系数衰减少，而且磨损率小。

Ionic charge accumulation at microscopic interfaces and volume conductivity of filled composites

复合绝缘材料微观界面处离子电荷的积累与体积电导率

Results indicate that the addition of right amount of PBT with low viscosity, ethylene copolymer A, rosin ester A and rosin ester B could improve the flowability of the composites to some extent without loss of their good mechanical properties and flame retardancy.

结果表明，适量加入低粘度PBT、乙烯共聚物A、松香酯A、松香酯B可使体系在保持综合性能较好的前提下，流动性能得到不同程度的改善。

Investigation on Dielectric Properties of Epoxy/ Crepe Paper Composites for Ultra-high Voltage DC Bushing

特高压直流套管用环氧树脂/皱纹纸复合绝缘体系介电性能的研究

The concept, formation conditions and formation mechanism of metal matrix intragranular composites were presented. The intragranular composite between α-Al and TiC leads to crystalline fracture.

提出了金属内晶型复合材料的概念、形成条件及其形成机理，分析了其发生穿晶断裂的主要原因是由于TiC与α&Al之间发生内晶型复合。

By assumption of periodical distribution of uniformed particles in size and shape, both hexagonal and cubic cell models were constructed to study mechanical properties of particle-reinforced composites by using three-dimensional finite element method.

利用三维有限元方法，通过建立立方体、六棱柱单位胞体数值分析模型，对颗粒增强复合材料做模拟计算。

Electron beam curing of resin matrix composites is a cost effective method compared with conventional heat curing.

与普通的热固化方法相比，树脂基复合材料的电子束固化是一种成本有效的固化方法。