composites的例句大全

The curing cycle of polymeric composites has significant effect on its performance and economic indices.

聚合物基复合材料的固化制度是影响其性能经济指标的重要因素。

POE can improve the composites fluidity, but is invalidation for the mechanical property, and degrade the wearing quality.

POE组分对于流动性能有一定的改进，但是对于力学性能的提高并没有明显的作用，然而对耐磨损性能影响却相当明显。

A study of milled glass fiber reinforced composites used as the strain gage backing material is present in this paper, which made it suitable more well for the demands of load cell.

为了满足传感器的使用要求，本文以玻璃纤维增强环氧树脂基复合材料薄膜作为传感器应变片的基底材料。

As for UHMWPE-base composites reinforced by Cu powder, the one whose filling Cu powder makes up 15% of the composite by weight has lower friction coefficient and smaller wear value than the others.

填料Cu粉质量分数为15%时的复合材料摩擦系数较小，磨损量较低；

Bending modulus of CF/ KF hybrid composites are on the rise with carbon fiber volume fraction increasing.

CF/KF混杂复合材料的弯曲模量随着碳纤维相对体积分数的增加而呈上升的趋势。

Effect of Fiber Surface Treatment on Interface Binding Strength of Kevlar Composites

表面处理对Kevlar纤维复合材料界面结合强度的影响

The effects of borax glass inhibitor content on oxidation resistance of C/ C composites was studied by oxidation experiments. The oxidation mechanism was analyzed on the basis of SEM results.

采用氧化烧蚀试验研究了改性剂硼玻璃含量对C／C复合材料抗氧化性能的影响，通过扫描电镜（SEM）观察分析了其抗氧化机理。

Failure Modes of Unidirectional Boron Fiber/ Epoxy Resin Composites for Repair of Damaged Aluminum

修复用硼纤维／环氧单向复合材料的破坏模式研究

Effects of aluminum alloy plate thickness on single-sided repair efficiency for boron fiber/ epoxy composites

铝合金板厚度对硼纤维/环氧复合材料单面修复效果的影响

The effects of parameters of hot pressing temperature, pressure, time and circumstance to mechanical properties of the B/ Al composites and boron fiber itself are analyzed.

从工艺的角度分析了复合工艺参数&温度、时间、压力和环境对B/Al复合材料及对B纤维的影响。

It is shown that the strengthening mechanism of the composites are secondly phase strengthening and grain refining, and the toughening mechanism is a synthetic effect in terms of grain refining, microcrack forming, crack deflection and crack branching.

ZrO2颗粒通过第二相强化和细化晶粒使复合材料强度得到提高，通过细化晶粒、裂纹偏转和分支、形成微裂纹等机制的综合作用增韧复合材料。

Argon gas atmosphere furnace brazing of SiC_p/ 101Al composites

SiC p/101Al复合材料的氩气保护炉中钎焊

Quality evaluation of ultrasonic brazing of aluminum matrix composites

铝基复合材料超声波辅助钎焊质量评价

Fiber breakage and its development in fiber reinforced composites

单向纤维增强复合材料中纤维断裂及其发展

The increase of the strength and toughness of SiC_p/ MoSi_2 composites is mainly attributed to the refinement of MoSi_2 grains, dispersion strengthening of the SiC particles and elimination of the brittle SiO_2 glass phase.

SiC p/MoSi2复合材料强韧性的提高主要是由于晶粒细化、SiC颗粒弥散强化以及脆性SiO2玻璃相的减少和消除。

This article studied the Cast-in-face process of Fast-dry coatings for producing the metal matrix composites face.

本文研究用快干涂料法来制造金属基表面复合材料的铸渗表面合金化工艺.

The Dynamic Characteristics of Several Unidirectional Carbon Fiber Composites at Ultra low Temperature

几种单向铺层碳纤维复合材料超低温下动态性质的研究

Study on the tribological properties of polyimide composites filled with molybdenum disulfide

二硫化钼填充聚酰亚胺复合材料的摩擦学性能

The multiple component sintering additive can also play double effects during preparing BN/ AlN composites, and plays important role on promoting densification process and improving property.

复合烧结助剂在制备BN/AlN复相陶瓷过程中同样可起到双重效果，对促进材料的致密化和改善材料性能起到了重要的作用。

Properties of dielectric breakdown of 2 2 piezoelectric composites in series were studied.

研究了串联2-2型复合材料的介电击穿特性.