flange的例句大全

Molded-in liner fully supported by valve body at flange seals.

模铸进的衬垫被整体固定在阀体的法兰密封处.

Mating pipeline flanges shall be standard reducing flange with I. D . to exactly match valve I. D.

匹配的管道法兰应该是标准的缩小法兰,其内径应该与阀门的内径完全一致.

Seat end of valve must be mated standard flat faced metal flange. Rubber flanges not acceptable.

阀门的阀座端口必须与平面金属法兰配合. 橡胶法兰是不可接受的.

With the NEMA standard flange connection keep the good universal.

采用NEMA标准的法兰连接,通用性好.

An O-ring located in nacelle flange is applied between the grease channels in nacelle and bearing.

在机舱润滑油脂通道和轴承之间有O形圈,O形圈位于机舱法兰上.

Fractured 1 Cr 18 Ni 9 Ti butt welding flange was analysed by OM, SEM and EDX.

用光学显微镜 、 扫描电镜和能谱仪分析了1Cr18Ni9Ti对接焊法兰盘断裂原因.

Mark the propeller shaft and pinion yoke, or pinion flange, for installation reference.

在传动轴和传动轴轴轭 、 或小齿轮轴轭上作标记, 作安装的参考标志.

This option saves cable and flange material and makes complicated, cost-intensive reworking of the enclosures unnecessary.

此选项可以节省电缆及法兰材料,而且使复杂, 高成本的机箱改造不再是必要的.

Remove cover and clean flange and reseal.

拆卸车轴护罩,清洁凸缘并重新密封.

Force the seal onto door flangContinue rearward until it is seated on flange.

用力将密封压到车门凸缘上,继续向后压直至它固定到凸缘上.

Flange at bottom, position monitoring optional, reinforced swing mechanism without overload protection device, double acting, max.

在底部, 位置监控可选, 法兰钢筋无过载保护装置的摆动机构, 双作用, 最大.

The composite beam is a component comprised the steel beam and the concrete flange plate beam.

组合梁是钢梁和其上混凝土翼板共同抗弯的一种构件.

Reverse Cycle Type: pump body mounted directly on the motor flange for easy vaporization of liquid.

逆循环型: 泵体直接装在电机法兰上,适用于易汽化液体.

Flange widely used wellhead equipment, oil trees and other well control equipment for connecting with.

法兰广泛用井口装置 、 采油树及其它井控设备,作连接用.

Gasket for 6-inch tank truck, round flange for 50 K gallon collapsible tank.

油罐车用的6英尺密封垫片,50K加仑折叠式油箱用的圆法兰.

Three structures have exhibited cracking at the ends of flange gusset plates.

已有三个结构在翼缘节点板端部出现了裂纹.

The colour markings, match points on the cardan shaft and on the all-wheel final drive flange must be aligned.

万向节轴和全轮驱动主驱动法兰上的彩色标记（匹配点）必须对齐。

Press the flange and replace the side sealing ring.

压紧法兰(均匀用力)更换侧密封圈.

Our company owns professional technic on making FRP flange, elbow, tee and other special products.

我公司采用专业的技术制做玻璃钢法兰.弯头.风门. 三通等特殊制品.

F 350 Flange is used in main bearing of TATUNG-OKUMA grinding machine series.

F350法兰用于大同磨床系列机床主轴使用.