flange的例句大全

Clean crankshaft flange carefully using acetone or solvent naphtha.

使用丙酮或溶剂石脑油仔细清洁曲轴法兰。

Fit the vibration damper on the crankshaft flange.

将减震器安装在曲轴法兰上。

Clean crankshaft flange and crankcase bore carefully.

小心地清洁曲轴法兰和曲轴箱孔。

Coat the sealing ring inside and out with fresh engine oil and pre-position it on the crankshaft flange.

用新鲜机油涂抹密封圈内外侧，并预先放在曲轴法兰上。

Carefully remove smaller edges or burrs on the chamfer of the crankshaft flange with an oilstone if necessary.

如有必要，请用油石仔细去除曲轴法兰倒棱上的小边或毛刺。

System Design and Characteristic Analysis of Movable Flange Facing Machine Tools

移动式法兰端面加工机床的总体设计与特性分析

The methods that can be used are: improve the cope hole; deal with the backing strip used for beam flange; strict the requirements for welding; reduce welding defects; remove the cracked parts; partial substitution of components.

采用的方法有：改进焊接工艺孔、对梁翼缘焊接垫板进行处理、严格焊接工艺要求，减少焊接缺陷、清除含裂纹部分、构件部分替换。

Describes a sleeve type compensator-the self balancing compensator, which can be used in heating networks to eliminate the blind flange force on primary fixing trestles.

介绍了一种套筒型补偿器&自平衡补偿器，它可用在热力管网中消除主固定支架的盲板力。

( b) When considering the bars in slab participate in beams against negative flexure, four or six times slab-thickness on each side of web can be defined as the effective flange width of slab by intermediate or rare earthquake actions.

当考虑板筋对梁端负弯矩承载力的提高作用时，可在设防烈度地震和罕遇地震作用下分别取每一梁侧四倍、六倍板厚范围作为板的有效宽度。

With the restraint of flange to web considered, the buckling stress of steel beam web under different stress is analyzed. The condition for instating web stiffener is given.

考虑翼缘对腹板的约束作用分析处于不同状态下钢梁腹板的临界应力，得出腹板加劲肋的设置条件激励与约束的关系；

Wear behaviour of swing motion bogie and cross-braced bogie nearly uniform, and the radial bogie can reduce the wheel flange wear effectively.

摆动式转向架和交叉支撑转向架车轮的磨耗行为比较接近，而径向式转向架能有效减轻车轮轮缘磨耗。

Leakage rate calculation of bolted flange connections

螺栓法兰连接系统泄漏率计算

Bolted flange sealing is widely used in process industry nowadays.

法兰密封在流程工业中应用广泛。

Advances of Research on Bolted Flange Joints at Elevated Temperature

高温螺栓法兰连接研究进展

3-D Finite Element Simulation of Bolted Flange Joint Considering Gasket Nonlinearity

考虑垫片非线性时法兰接头性能的三维有限元模拟

The Heat Transfer Model between Bolt and Bolt Hole of Bolted Flange Sealing

法兰密封中螺栓与螺栓孔的传热学模型建立

Trends of Bolted Flange and Gasket in European Standard

欧洲螺栓法兰设计和垫片标准的新动向

It is composed of casing flange, casing cross joint, wellhead valves, tubing hanger, tubing head cross joint and accessories.

这种井口装置由套管法兰、套管大四通、井口阀、油管挂、油管挂体及相关附件组成。

When the flange hole of coal blower casing and inlet box is countersunk, the problem of connecting hole back spot facing can be effectively solved.

它可以有效地解决在锪煤气鼓风机铸铁机壳和进气箱的开箱法兰把接孔时，连接孔背面的锪平问题。

The Extrusion Dies CAD System Development of Light Alloy Wainscot with Flange based on VB 6.0

基于VB6.0的轻合金带筋壁板挤压模具CAD系统开发