joint的例句大全

A Study on the Tangential Dynamic Characteristic Parameters of Bolted Joint

螺栓结合部切向动态特性参数的实验研究

Fatigue Design of Bolted Joint in a Steel Structure

金属结构中螺栓联接的疲劳设计

Nonlinear Model of Bolted Joint and Its Wave Energy Dissipation

螺栓接头非线性模型及其波能耗散

Strength studies on non-even distribution bolted joint in composite laminates

复合材料非均匀分布多钉连接强度研究

A Test Research on Fretting Damage of Bolted Joint and Its Coating Glue Protection

螺栓联接件的微动损伤及其涂胶防护试验研究

Results showed that the ductility of bolted splice joint is much better than that of the welded one;

试验结果表明：螺栓拼接节点的延性远好于梁柱焊缝连接；

In this study, effect of cyclic load on the vacuum tightness of the adhesively bonded joint was investigated experimentally.

该文实验研究了循环载荷对粘接接头气密性的影响。

Review on residual thermal stress of ceramic bonded joint with metal

陶瓷与金属焊接接头残余热应力研究

Damage to the bonded joint if the waiting time is not observed before further work!

如不遵守等待时间而急于展开下一步工作，粘合处将受损！

Effect of process parameters and interlayer on properties of 1420 Al-Li alloy diffusion bonded joint

1420铝锂合金扩散焊工艺及中间层材料对接头性能的影响

Effect of Alkaline Anodization Treatment of Durability of Titanium/ Epoxy Bonded Joint

碱性阳极化处理对钛合金／环氧胶接接头耐久性的影响

The results showed that the aging of epoxy bonded joint in water was accelerated by increasing temperature.

结果表明，提高温度可以加速环氧胶接接头在水中的老化；

Ultrasonic aluminum wire bonder and ultrasonic gold wire bonder are mainly applied to joint the chip pad with the lead-frame in the later process of semiconductor producing.

超声铝丝焊接机和超声金丝球焊接机主要运用于半导体生产后工序中芯片焊盘与外框架间引线的焊接。

TEM study of bonding layer in Cu-Al explosively welded joint

Cu－Al爆炸焊结合层的透射电镜研究

Study of Heat Treatment Technics on Carbide Joint by High Frequency Induction Brazing

高频感应钎焊硬质合金接头热处理工艺研究

Interface Behavior and Joint Strength by TIG Arc Brazing for Titanium and Titanium Alloy

钛及钛合金电弧钎焊及接头强度

Joint strength and fracture analysis of arc brazing with Cu based filler metals

Cu基钎料电弧钎焊接头强度及断口分析

Experimental Research on Torch Brazing Solder for Al-Cu Joint Welding

铝－铜火焰钎焊材料研究

Influence of Cu on microstructure of soldered joint in Al brazing with rapid-solidifying Al-Cu solder

快速凝固Al-Cu钎料钎焊铝Cu对钎缝组织的影响

The brazing-ability and quality of brazed seam of 6063 aluminum alloy brazed by Al-Si eutectic filler metal and QF flux is discussed by means of test of spread-ability and test of T joint.

本文用平百铺展试验和T型接头试验，研究了6063铝合金采用AI－St钎料和氟化物钎剂（QF钎剂）钎焊时的钎焊性和钎缝质量。