layer的例句大全

The EIS results of bonded coating indicate that three time constants were obtained during the initial immersion period, and then a new time constant appeared due to the formation of rust layer.

而对于有粘结层的涂层，其交流阻抗谱在浸泡初期具有3个时间常数，浸泡后期由于在碳钢表面生成了一层腐蚀产物，出现了1个新的时间常数。

On Manufacture of Foods by Processing Wheat Bran& Bran Flour and Aleurone Layer Flour

小麦麸皮加工成食品的探讨&麸皮面粉、糊粉层面粉

By the use of forward modeling method, study into the P I oil layer formation sand-mud interbed effect of structure on characteristics of seismic reflection.

利用正演模拟手段，研究葡一油层组砂泥岩结构对地震反射特征的影响。

The structure of compoud 4 consists of left-handed and right-handed helical chains that are connected through bridging oxygen atoms to form a two dimensional layer structure.

该化合物由四面体ZnO3N、假四面体HPO3相互连接形成左手和右手螺旋链，这些螺旋链之间通过桥氧原子连接形成二维层状结构。

Observation and analysis of surface wind field, sea and land breeze and internal boundary layer;

地面风场、海陆风及内边界层的观测与分析；

Secondly, it brings forward that it is a practical technical and structure mode to use the multiple preventing layer as the water preventing and draining system in highway tunnel of loess.

然后在总结现有公路隧道防排水技术特点的基础上，提出了黄土公路隧道防排水系统宜采用复合防水层为主的适用技术与结构型式，得出了一些有益的结论。

In the forced feeding experiment, the relationship between the nutrient contents in layer manure and their dietary intake was analyzed;

通过强饲试验考察蛋鸡摄入各成分量与排出粪便中肥料成分含量之间的相关关系以及饲料组成对其排出粪便中肥料成分含量的影响。

What's more, a simple FAT file system has been established on the application software layer of USB host system to fulfill reading the data saved in the U disk in the process of engraving the work piece.

在USB主机系统中的应用软件层上建立了一个精简的FAT文件系统，从而使得雕刻机系统在实际加工过程中能够对存放在U盘中的加工数据进行读取。

The data of 5 ionospheric vertical sounding stations before 4 earthquakes in Japan are analyzed. It is found that most of the critical frequencies of the E sporadic layer tended to decrease and the only few tended to increase around the epicenters before and after the earthquakes.

分析日本4次地震前5个电离层垂测站资料，发现地震前后震中附近夜间电离层偶发E层的临界频率f0ES值多数呈下降趋势，少数呈增加趋势。

In this example, the first layer of tar felt is nailed to the boarding and the subsequent layers are bonded to each other in hot tar.

此例中，第一层油毡是用钉子钉在木板上的。上面的几层油毡是用热沥青粘合起来的。

The Al element in the substrate diffuses into the brazing seam, forming a thin reaction layer in the interface region.

焊接母材中的Al元素向焊缝发生了扩散，在界面区形成了一层很薄的反应层。

However, the composite layer material itself has a very complicated manufacturing process. As differences in manufacturers or production technology, solder thickness and uniformity will affect the heat transfer during brazing and solder flow, which create difficulties for the brazing process.

而复合层材料本身就是很复杂的制造过程，由于生产厂家或生产技术的差异，钎料层厚度及均匀度会影响钎焊时的传热与钎料的流动情况，为钎焊工艺带来困难。

The results suggest the joint is not ideal if the Cu layer is too thin or too thick, and it is very important for existing some eutectic substance in brazed seam.

研究表明，Cu层的厚度太薄或者太厚，其连接效果都很不理想，同时在Al合金与Cu中间层接触反应钎焊中，钎缝区存在适当的液相对于提高接头强度是至关重要的。

Study on Distribution of Injected Carrier Densities in the I-Layer of a Forward Biased PIN Diode

PIN管正偏注入的载流子在Ⅰ层中分布的研究

TEM study of bonding layer in Cu-Al explosively welded joint

Cu－Al爆炸焊结合层的透射电镜研究

Technique, such as electronic probe, XRD, optical microscope, micro-hardness and macro hardness test, are applied to investigate the microstructure, phase structure, and analyze the alloy element distribution of metallurgical bonding layer and the material mechanical property changes.

利用电子探针、XRD、光学显微镜、显微硬度和宏观硬度测试等手段，研究扩散件试样的显微组织、物相结构，分析冶金结合层中合金元素分布和材料内部力学性能变化。

The capability variation rule of bonding layer was also analysed.

采用滑动磨损法检测了耐磨性，并分析了衬瓷层性能的变化规律。

The Distributed Force Model of Intelligent Beam Structures Based on Effect of Bonding Layer

考虑粘贴层影响的智能结构梁分布力模型

Two dimensional finite element analysis of ceramic veneer bonding layer

对瓷贴面粘结层的有限元应力分析

Lead in the plating layer of high voltage diodes on the basis of a zinc borate glass body.

以硼酸锌玻璃体为基础的高压二极管的电镀层的铅；