modulus的例句大全

Adopting high-strength and high-modulus alkali-free glass fiber, it is knitted into loom.

采用 高强 高模量无碱玻璃纤维, 经过经编定向织造网格坯布,通过改性沥青涂覆加工成玻璃纤维格栅.

Constant modulus algorithm ( CMA ), which was used in blind equalization, is introduced in this paper.

文中引入了用于盲信号均衡的恒模算法 ( CMA:constant modulus algorithm ).

These two parameters are nowadays called the modulus of compressibility.

这两种参数现被称为压缩模量.

At the same time, the spatial distribution of deformation modulus is obtained.

最后, 初步得出了此巷道围岩变形模量的空间分布规律.

Expounded punching, blanking, bending modulus of the composite structure design and principle.

阐述了冲孔 、 落料 、 压弯复合模的结构设计及工作原理.

The fibers with moderate abrasion resistance include wool, cotton, and the high wet-modulus rayons.

具有中等耐磨损性能的纤维有羊毛 、 棉花和高湿模量粘胶纤维.

The stress-relaxation modulus is a continuous, decreasing function.

应力松驰量为连续衰减的函数.

The various types of stress, strain, and elastic modulus are summarized in Table 10-3 .

各种应力 、 应变和弹性模量列于表 10-3 中.

The larger the elastic modulus, the greater the stress needed for a given strain.

弹性模量越大, 产生一定应变所需要的应力也越大.

Keywords: geometric nonlinearity, sag effect, equivalent modulus of elasticity, vehicle-bridge interaction.

关键词: 几何非线性 、 中垂效应 、 等效弹性系数 、 车桥互制.

The real part of the modulus is often called the storage modulus.

与应变同相的实数部分模量,通常称为储能模量.

The method does not need precoding or constant-modulus ( CM ) modulating.

该算法无需 预编 码或恒模调制.

We can gain the isochronous-modulus curves from the curves of stress-strain ratios.

根据岩石蠕变的应力 - 应变比曲线可以近一步分析得到等时模量曲线.

Results show that the Young's modulus is continuously reduced by hydrogen.

结果表明氢连续降低合金的弹性模量.

High-modulus polypropylene compound was developed by means adding nano-meter montmorillonite to polypropylene.

通过在聚丙烯中添加纳米蒙脱土的改性方法,开发了高模量聚丙烯专用料.

The results show that the maximum elastic specific energy in the wall of coal roadway is almost directly proportional to the square of digging depth and almost inverse proportional to the elastic modulus.

结果表明，煤层巷道两帮煤体中弹性比能的最大值与采深的平方近似成正比，与其弹性模量近似成反比。

Bending modulus of CF/ KF hybrid composites are on the rise with carbon fiber volume fraction increasing.

CF/KF混杂复合材料的弯曲模量随着碳纤维相对体积分数的增加而呈上升的趋势。

Through analyzing the temperature field and stress field of typical steel castings some casting parameters as modulus, the distance of feeding head, cold iron are validated and modified, which is in accordance with the production-lines.

通过选取典型的铸钢件，采用实验的方法，对温度场、应力场、模数、冒口补缩距离、外冷铁等铸造工艺参数进行验证并加以修改，使其符合生产实际。

For gas bearing sandstones , Lame constant will reduce and shear modulus increase.

获得了莺歌海盆地砂岩纵、横波速度关系.

Investigation of influence factors on bending modulus of carbon fiber/? Epoxy

碳纤维/环氧复合材料弯曲模量影响因素的研究