reducer的例句大全

Lightnin reducer allows you to change the seal without removing gear driver.

维修和更换密封不需要移动莱宁的齿轮箱传动系统.

Check and empty residual rust-preventative oil inside the gear reducer.

检查并排放干净减速机内部的残留润滑 防锈 油.

Check pipeline and gear reducer for leak everyday.

每天检查一次管路和减速机是否存在漏油现象.

The viscosity reducer A-1 was synthesized from acrylic amide by radical polymerization and high molecular reaction.

以丙烯酰胺为原料,通过自由基聚合和高分子化学反应合成了降粘剂A -1.

Synthesis of amino-sulfonic acid-based high performance water-reducer and testing results of later stage concrete were discussed.

本文主要讨论了氨基磺酸系高性能减水剂的合成过程及后期混凝土试验情况.

Reducer, crank pin bearing so small and no reverse impact load that reducer tooth broken, crank pin fracture will not happen.

减速机、曲柄销受力小，无反向冲击负荷，减速机打齿、曲柄销折断的故障不会发生。

The bell reducer provides the cyclone action and the boundary layer control.

喇叭形异径管产生旋风作用并进行边界层控制.

Check for dust blockage on respirator of oil system and respirator of gear reducer.

经常检查油系统呼吸器和减速机上呼吸器是否有粉尘堵塞.

Rotating reducer is an important part of blast hole , it holds biggest loads while drilling.

回转机构是牙轮钻机的重要工作部分, 在钻孔作业中承受最大的负荷.

Caution : It is prohibited to lift the gear reducer with bolt holes on output drive flange.

注意! 严禁用减速机输出传动法兰上的螺栓孔起吊减速机.

Extrusion System: frequency variable motor, cycloidal pin gear speed reducer and high qualitynitrifiedfeed cylinder screw.

挤出系统: 变频调速电机 、 摆线针轮减速箱加优质氮化料筒罗杆.

Pinhole machining of pin gear housing is one of important procedures in manufacturing cycloid speed reducer.

针齿壳销孔的加工是摆线针轮减速器制造的重要步骤之一.

Planar double-enveloping reducer is used for paper cutting drive, fast cutting speed, low noise . G.

切纸传动采用平面二次包络减速机传动, 裁切速度快, 噪音更低.

The large opening of the bell reducer keeps air velocity low thus preventing moisture re-entrainment.

喇叭形异径管的大开口度使空气流量保持较低从而避免把水分再次带走.

Rotary kiln drive system is mainly composed of electromotor, reducer, big ring gear and small gear.

回转窑传动系统主要由电动机 、 减速机 、 大齿圈和小齿轮组成.

The properties of filtrate reducer used in MMH drilling fluid are evaluated.

介绍了一种与正电胶钻井液配伍的降滤失剂,分析了它的反应机理,并对该产品的性能进行了评价.

These could be good fundamentals for improving the design of harmonic gear reducer and their performances.

为谐波齿轮减速器的设计,提高其工作性能打下了良好的基础.

NGW , TP series planetary gear reducer.

TP系列行星齿轮减速机.

In order to solve the selflocic problem , the NGWN type planetary gear reducer is released.

为解决减速器自锁问题推出NGWN型行星齿轮减速器.

On the base of exact analysis offeree for the double crank ring-plate-type cycloid drive, we building 3-D solid model and drawing the CAD paper for the double electromotor drive the double crank ring-plate-type cycloid reducer.

在双曲柄环板式针摆行星传动准确受力分析的基础上，对双电机驱动双曲柄四环板式针摆行星减速器进行三维建模并绘制CAD图纸。