scanning的例句大全

Differential scanning calorimetry ( DSC) was employed to investigate the relation of deformation rate and eutectic melting activity energy of AZ91D magnesium alloy by SIMA method.

采用DSC技术研究了SIMA法制备半固态AZ91D镁合金坯料过程中形变率与共晶熔化激活能的关系。

Diagnostic Value of CT Scanning on Extrahepatic Cholestasis Biliary Cirrhosis

CT扫描对肝外梗阻性胆汁性肝硬化的诊断价值

Purpose: To study appearance of CT scanning of extrahepatic cholestasis biliary cirrhosis ( ECBC) and value of CT in diagnosing ECBC.

目的：探讨肝外梗阻性胆汁性肝硬化的CT诊断价值。

CT scan and prognosis for 27 cases of acute diffuse brain swelling ( ADBS) in head injury are reported in this study. CT scanning is characteristic of displaying compressed or obliterated lateral ventricles, third ventricle and basal cisterns.

27例脑外伤后急性弥漫性脑肿胀的CT表现以侧脑室、三脑室及基底池受压或消失为特征。

The results of differential scanning calorimetry ( DSC) showed that the decomposition temperature of ACPA decreased when it was chelated onto the particles.

差热扫描量热分析表明偶氮引发剂与纳米碳酸钙螯合后分解温度略有降低；

At the same time the transformation points, Ac1, Accm and Ms were measured using thermal dilatometer and differential scanning calorimeter. Then different isothermal transformation treatments of the steels were carried out.

同时利用膨胀法和差示扫描量热法测定了两种钢的相变点Ac1、Accm和Ms。然后对试样进行了不同工艺的低温等温转变处理。

A Portable Off-line OCR and Bi-linguistic Translation System ( Chinese to English, English to Chinese) embedded in DSP has been designed which is called Electronic Reading-Pen. The whole processes including scanning, off-line OCR and translation are implemented on it independent of computers.

开发了以DSP为核心的扫描识别及英汉互译系统（电子阅读笔），在小型手持设备上实现了从扫描输入图像到脱机OCR以及翻译显示的处理，并且完全独立于计算机工作。

The digital image was captured by scanning standard photograph of cotton yarn.

本文用扫描仪采集标准样照图象.

Methods The alumina powder size mass distribution was obtained by BI XDC powder size analysis device; the open pore parameters of alumina adobe and sintered body were analyzed using the mercury pressure method. Their fracture surfaces were observed under scanning electronic microscope.

方法用BI-XDC粒度分析仪分析氧化铝粉体粒度的质量组成，压汞法测试氧化铝坯体和1125℃烧结的氧化铝烧结体的开孔孔隙分布特征，扫描电镜观察氧化铝烧结前后的微观结构。

Multidimensional Super-Resolution Estimation of Scanning Antenna with WSF Algorithm

用WSF算法实现机扫雷达多维超分辨估计

To analyze the influence of external vibration on the tip-sample interaction of scanning probe microscope ( SPM), a concept, vibration rejection ratio ( VRR), was proposed.

为分析外界振动对扫描探针显微镜（SPM）针尖-样品副的影响，提出抑振系数的概念。

The Value of Immediate CT Scanning in Diagnosing UPJ Obstruction in Children after IVP

IVP后CT扫描诊断小儿肾盂输尿管连接部梗阻

The result showed that the analyzer has wide input frequency range, narrow RBW ( Resolution Bandwidth) and high scanning accuracy, and it reaches the international advanced level.

测试结果表明所设计的分析仪输入频带宽、频率分辨力和扫频准确度高，达到国际同类产品先进水平。

Chase after the wave Effect of PZP on the optical scanning holography

菲涅耳波带板在光学扫描全息术中的作用

This paper dealt with ways of utilizing to the most extent the word textual resource the thesis author submitted by combining such softwares as Photoshop, word with such hardware facilities as scanning when adopting Founder typesetting software as priority.

讨论了在采用北大方正排版软件作为主要书版排版软件时，如何结合Photoshop、word等软件及扫描仪等硬件设施，充分利用作者提供的word文件资源；

In the end, this article describes the design and implementation of a network vulnerability scanning system, which names NVS ( Network Vulnerability Scanner).

最后本文设计并实现了一个采用木马体系结构的、面向攻击的网络漏洞扫描系统NVS（Network Vulnerability Scanner）。

Electron microscope scanning surface morphology and XRD analysis showed that inhibitor NNF reduce the increase in the oxygen, sulfur, to form a continuous dense FeS protection film, preventing corrosion.

电镜扫描表面形貌分析和XRD表明，缓蚀剂NNF使氧元素增加、硫元素减少，能形成连续致密的FeS保护膜，阻碍了腐蚀的发生。

The processing for dimension stability of metal scanning mirror in airborne scanner

航空扫描仪中金属扫描镜的尺寸稳定化处理

Incremental updating algorithms ( IUA) for discovered association rules are employed to decrease the cost of scanning the original transaction database.

关联规则增量更新算法可以减少对交易数据库的访问。

With the change of scanning speed, the size tolerance of the PP part exhibited a minimum.

随着扫描速度的变化，试件翘曲量存在极小值。试件的尺寸误差随着激光功率增大、扫描速度降低或铺粉厚度减小而降低。