seam的例句大全

I felled the seam of my trousers.

我把裤子的边缝缝上了.

In appearance, the welt seam is similar to the wrong side of the flat fell seam.

外观上与明包缝的反面相似.

To prevent a seam from stretching, sue a twill tape to support the seam.

为了防止缝线伸长, 用斜纹布贴带加以固定.

The results suggest the joint is not ideal if the Cu layer is too thin or too thick, and it is very important for existing some eutectic substance in brazed seam.

研究表明，Cu层的厚度太薄或者太厚，其连接效果都很不理想，同时在Al合金与Cu中间层接触反应钎焊中，钎缝区存在适当的液相对于提高接头强度是至关重要的。

The question on the multi-seam mining under closely spaced architectural complex in city and its countermeasures

城市密集建筑群下多煤层开采存在的问题及对策

The simulation mentioned above was confirmed by series experiments, and the proper thickness of the brazed seam is 50~ 80 μ m for the CRB joint of Al with Si as an interlayer.

在试验证明FEM计算结果的可靠性的基础上，给出了Si为中间层进行LF21铝合金接触反应钎焊时，其合适的钎缝宽度范围是50～80μm。

The results of the gas outburst simulation experiments showed that there was no difference in an air-flow reverse phenomenon in air inflow roadway between the upward ventilation and downward ventilation when the seam angle is ranging from 0 to 32 °.

煤层倾角在0~32°内变化，突出瓦斯相似模拟实验结果，看不出上行风和下行风对进风平巷风流逆流现象有何差别。

The brazing-ability and quality of brazed seam of 6063 aluminum alloy brazed by Al-Si eutectic filler metal and QF flux is discussed by means of test of spread-ability and test of T joint.

本文用平百铺展试验和T型接头试验，研究了6063铝合金采用AI－St钎料和氟化物钎剂（QF钎剂）钎焊时的钎焊性和钎缝质量。

The Al element in the substrate diffuses into the brazing seam, forming a thin reaction layer in the interface region.

焊接母材中的Al元素向焊缝发生了扩散，在界面区形成了一层很薄的反应层。

Effects of Heat Treatment on Properties of Brazing Seam

热处理对硬钎焊焊缝性能的影响

A new method to improve the heat resistance of the brazing seam

提高钎缝耐热性的新途径

X ray image analysis of high temperature brazing seam for corrugated plate sandwich structure

波纹板夹层结构高温钎焊焊缝X射线影像分析

Effect of alloy powder on Microstructure of brazing seam

钎缝中合金粉对组织的影响

The welding residual stresses exist mainly within 15 mm from the brazing seam.

焊接残余应力主要分布在离钎缝15mm以内的区域。

The logistic arm must seam lessly deliver material as needed.

后勤部队必须及时输送所需物资.

There is a certain angle between caving line and coal seam strike.

垮落线与煤层走向是一定角度。

Remining coal seam left in caving zone

浅析开采冒落带内丢煤的复采

The height of the watering fissures is 21.5m because the height of caving zone is about 10m after the mining of all the 3 seam ( 4 layers), and the result basically accord to the result of theoretic calculating and numerical simulation;

3煤层全采后（4个分层）垮落带高度为10m左右，导水裂隙带的高度为21.5m，与理论计算和数值模拟结果基本一致；

Surface subsidence patterns for mining ore seam with anticlinal structure

背斜构造矿层开采地面沉陷规律研究

Repeat this procedure at the finish of the seam.

在终端重复这道程序.