shaft的例句大全

Because of low fatigue limitation of shaft enduring dynamic-load stress rupture is happened.

对此,在提高轴头疲劳极限和降低变应力两方面采取了相应的改造措施.

Strong load capacity of shaft , service life long.

轴载荷能力强, 工作寿命长.

This paper presents an intelligent control for cement vertical shaft kiln via peripheral blowing.

介绍了组合腰风水泥立窑智能控制系统.

The circular tube belt conveyor is a new method for hoisting coal in a vertical shaft.

圆管胶带输送机是竖井提升煤炭的一种新方法.

Mine shaft hoist system accidents occur occasionally, causing casualties, while also caused damage of the equipment, the duration of the delay or interruption of production, seriously affected the normal conduct of the mine production activities.

矿山竖井提升系统事故时有发生，造成人员伤亡的同时，也造成了设备的损毁、工期的延误或生产的中断，严重影响了矿山生产活动的正常进行。

Investigation on the shaft neck fatigue crack of helicopter rotor hub

直升机旋翼桨毂轴颈疲劳裂纹探讨

Field test study of methods for supporting large-section inclined shaft in gravel layer

卵砾石层大断面斜井井筒支护方法现场试验研究

The shaft seals use quality mechanical seal.

采用加长轴电机直联结构,轴封采用优质机械密封.

Shaft seal: it can use mechanical seal, dynamic seal and packing seal, at theoption of users.

轴封: 采用机械密封 、 动力密封及填料密封, 用户可以任意选定.

The shaft seal can adopt soft gland packing or mechanical seal for selection.

泵的轴封有软填料和机械密封两种供用户选用.

There is 2 CY gear pump series pump body, cover, gears, bearings and the shaft sealing etc.

2CY系列齿轮油泵是有泵体 、 泵盖 、 齿轮 、 轴承套以及轴端密封等零部件组成.

Likewised, should the mechanical shaft seal assembly require replacement, the gear set dose not have to be removed from the pump.

同样地，机械密封轴部件取代，不需要从泵体上移除。

In the mill shaft coupling, its external gear set also often uses the circular arc drum-shaped gear.

例如，在轧钢机联轴器中，其外齿套往往采用圆弧鼓形齿轮。

Remove the rear propeller shaft.

拆卸后传动轴.

Install the straps and bolts to hold the propeller shaft to the yoke.

安装扣夹和螺栓,将传动轴固定到轴轭上.

The propeller shaft frequency is one of the important target recognition features for passive sonar.

螺旋桨轴频是被动声纳极其重要的目标识别特征之一.

The pinion gear is attached to the steering shaft.

该齿轮连接转向轴。

Forward extruding for hollow pinion gear, compound extruding for housing gear and upending extruding for shaft gear and their forming conditions and processes were analyzed.

介绍了带孔小齿轮的正挤压直接成形、带壳小齿轮的复合挤压成形和带轴齿轮的镦挤成形等传统冷挤压方法，以及上述各类齿轮的冷挤压成形条件和工作过程。

The screw shaft diameter is 20. 5 mm;

丝杠直径为20.5mm；

Main press cut roller adopt universal shaft driving, which is advanced in designing.

主要压切辊采用万向轴传动, 传动设计先进.