shaft的例句大全

Shaft to ventilation and excavation, repair qanat soil when used.

竖井是为了通风和挖掘 、 修理坎儿井时提土之用的.

The start shaft is an integral part of the clutch assembly.

开始竖井不可分割的一部分的离合器总成.

The characteristic and mechanical mechanism of shaft failure under mega-thick alluvial surface layer are briefly analysed.

简要分析了位于巨厚冲积层表土下,竖井破坏的特点及力学机理.

The paper develops the analytic theory of ground consolidation shaft of un-striking through semi-permeable horizontal bed.

本文发展了考虑半透水下卧层的未打穿竖井地基固结解析理论,并分析了此类地基的固结基本形状.

An experimental investigation of the shrouded centrifugal backswept impeller flow field has been conducted at off-design flow using Laser Doppler Velocimeter ( LDV) and shaft encoder.

利用激光多普勒测速仪（LDV）对后弯闭式离心叶轮内部气流在非设计工况下的流动进行了实验测量。

This thesis presents the design and implementation voltage vector-controlled induction motor drive without any shaft transducer.

本论文的目的为设计与制作不用测速计之交流感应马达转速控制系统.

The main parts in the upper structure that bear pressure are of pipe truss structure and pin shaft link.

本机上部结构的主要受压构件为管绗结构，销轴连接。

Discussion of Connection Mode of Impeller and Main Shaft in Centrifugal Fan

离心通风机叶轮与主轴联接方式的探讨

The bearing inner races were a tight fit to the table shaft.

轴承的内圈与台轴采用紧配合.

Dilatable Bone Nail Applied in 17 Cases of Humerus Shaft Fracture

可膨胀髓内钉在17例肱骨干骨折中的应用

To observe the clinical effect of dilatable bone nail on humerus shaft fracture.

探讨可膨胀自锁髓内钉治疗肱骨干骨折的临床疗效。

The application of all solutions and algorithms were illustrated with a typical shaft-like parts drawing.

以轴类零件图为例,详细分析了作业图批改的若干关键技术,并给出了相应的算法和程序流程图.

This paper briefly describes the new shaft type scrap preheating system called UL BA developed by Japanese Nippon Steel Corporation.

文章简要介绍了日本新日铁开发的新型竖炉式废钢预热系统，即：UL-BA方式预热装置。

One end of the central axis connects the output shaft of the driving device.

中轴一端与动力机构的输出轴相接.

Installation of software of No 1 Military Project for client and its maintenance Installation of Shaft

军字一号客户端软件系统的安装及客户端维护竖井井筒装备一次成型

Design and Construction of Big-calibre Bench Mark of Shaft Type

大口径竖井式基岩水准标设计与施工

Knife shaft can be 360 degree adjusted by electric control.

刀轴可做360度电动控制相位调整.

The graphs of incidence light power and receiving light power VS shaft angle have high CMRR.

以接收光功率与入射光功率比映射轴角曲线关系具有高的共模抑制比.

A simple, feasible and economic way is introduced to construct the inclined shaft cross drift sand.

介绍一种简便 、 易行、经济、实用的斜井施工通过流砂层的方法.

Bare shaft, lever-lock flow control handle, worm gear operator, electric and pneumatic actuators.

裸轴, 水平杠杆固定流量控制手轮, 蜗轮操作装置, 电动和气动驱动装置.