simulation的例句大全

Computer Simulation of Extravehicular Activity Based on Torque Ratio Optimization

基于力矩比优化的航天员舱外活动仿真

With the simulation calculation of dynamic model, it indicates the extra eccentric mass of wheel is the main reason for shimmy.

通过对动力学模型的仿真计算，发现车轮过大的偏心质量是导致摆振的主要原因。

The mathematical model for the motion of CVE 2 type chaotic vibration exciter was set up and its numerical simulation and chaotic identification were carried out.

建立了使用滑动轴承的CVE-2型混沌激振器所产生的运动的数学模型，并对其进行了数值仿真和混沌识别。

Application of some actual evapotranspiration models in simulation of soil moisture

几种实际蒸散计算方法在土壤水分模拟中的应用

Meanwhile, the simulation calculation results are analyzed to find out the pressure difference between flash evaporator and condenser under which indicates the power of the constant operation of the desalination system. 2.

同时，利用仿真模型，重点分析计算了不同参数下闪蒸器与冷凝器之间的压差，分析系统持续运作的理论动力。

Numerical simulation and performance optimization for air-cooling dry evaporator coil in wet condition

湿工况下冷却空气型干式蒸发器盘管的数值模拟和性能优化

Performance Simulation and Optimization Analysis of Falling-Film Evaporator with Horizontal Tube Bundle Analysis of Corrosion Failure of Tube in Surface Evaporative Air Cooler and Protection

水平管式降膜蒸发器性能仿真及优化分析表面蒸发式空气冷却器管束腐蚀及防护

Mathematical model and simulation of the evaporating surface in a once-through boiler

直流锅炉蒸发区域的数学模型及其仿真

Trends Dynamic Simulation of the Eutectoid Transformation of Nodular Cast lron

球墨铸铁共析转变组织的动态模拟

Multi-phase field simulation of unidirectional solidification for binary eutectic alloys

二元共晶定向凝固的多相场法数值模拟

Mathematical Model for Ester Interchange Tower& the Simulation of Distillation with Reaction

聚酯酯交换塔的数学模型&反应精馏塔的模拟计算

Simulation test study on sludge centrifugal dewatering in urban sewage treatment plant

城市污水厂污泥离心脱水模拟试验研究

Moreover, the invariants of the stress deviator were employed to analyze the metal deformation process of ring compression and hydro-bulging toroidal shell by numerical simulation, and also the simulated and experimented results have a good agreement.

并且通过数值模拟的方法，采用偏应力张量不变量对圆环压缩和环壳液压胀形过程中金属的变形进行了分析，模拟结果和实验现象一致。

Then the lattice hydrodynamic model with the onramp system is proposed and the stochastic and deterministic onramp simulation methods are designed.

随后提出了匝道系统的格子流体力学模型，并设计了随机型和确定型匝道两种数值模拟方法。

Deterministic computer simulation is widely used in science and technology.

确定性计算仿真在科学研究和工程技术中的应用非常广泛。

The paper establishes the deterministic simulation model using the theory of sine summation. The model parameters are determined using the Method of Equal Distances and the Method of Equal Areas.

用正弦和理论建立了信道的确定性仿真模型，并用等面积算法和等距离算法确定了模型的参数。

It is not economical and maybe brings about negative control effects to make control strategies by deterministic simulation with typical conditions and faults according to conservative principles.

按典型的工况和故障的确定性仿真及保守原则制定控制策略，其决策不但不经济，还有可能带来危险的负效应。

Deterministic Simulation Model for Mobile Fading Channel

移动衰减信道确定性的仿真模型

Numerical Simulation on Molten Steel Flow and Circulation Flow Rate in RH Vacuum Degassing Process

RH精炼过程钢液流动行为与循环流量数值模拟

By debugging model, analyzing parameter error and sensitivity to take on water resources forecasting simulation.

通过模型调试，参数误差与灵敏度分析，进行水资源预测模拟。