simulation的例句大全

Especially we exploit the new modeling methodologies to fasten the behavioral simulation in the bottom-up verification of mixed-signal system.

特别是在混合信号系统自下而上的验证过程中，利用新的建模方法加速电路的行为级模拟。

Agent-based simulation is a bottom-up method for financial complex systems.

基于Agent的金融市场仿真是一种自底向上的金融复杂系统研究方法。

In this paper, the mechanical system of the bouncing ball was discussed and the corresponding computer simulation was established. Then we can observed kinds of dynamic behaviors of the bouncing ball.

本文讨论了反弹球的力学系统，建立了相应的计算机模拟，从中可观测到反弹球的多种动力学行为。

Research on Modeling and Simulation of Aircraft Electric Braking System

飞机全电刹车系统建模与仿真研究

The computer simulation and parameters optimization for the Scherbius dynamic braking system

串调动力制动系统的计算机仿真及参数寻优

Aiming at the result of simulation, braking time and braking efficiency was analyzed.

根据刹车系统仿真结果，对刹停时间、刹车效率等性能进行了分析。

Calculation of Braking power per Unit Area and Its Determination by Simulation Tests

单位面积制动功率计算及其试验确定

The simulation results suggested that the EVAP showed significant effects on the nucleation and growth of the paraffin crystal when the acetate concentration was around 30% and there existed one branched methyl group near the acetate group in each block.

在各种乙烯醋酸乙烯丙烯（EVAP）降凝剂中，当EVAP酯含量在30%左右，且在每个链段含有一个靠近酯基的甲基支链时容易在蜡晶的成核和生长过程中发挥作用。

Simulation results indicate that the bi-level branched channel structure, horizontal extending ranges and maximum vertical electric field changes are in good agreement with the corresponding observed data.

得到的云闪双层、分叉通道结构，通道的水平和垂直延伸范围以及放电前后最大垂直电场变化值与观测的相应结果有更合理的一致性；

The simulation mentioned above was confirmed by series experiments, and the proper thickness of the brazed seam is 50~ 80 μ m for the CRB joint of Al with Si as an interlayer.

在试验证明FEM计算结果的可靠性的基础上，给出了Si为中间层进行LF21铝合金接触反应钎焊时，其合适的钎缝宽度范围是50～80μm。

Numerical Simulation and Analysis of the Temperature Field for Direct Current GTAW Arc Brazing

直流GTAW电弧钎焊温度场的数值模拟及分析

Simulation of vibration amplitude distribution during ultrasonic brazing

超声波钎焊过程中振幅分布的数值模拟

The virtual simulation model and control logic of chassis group and sub-assembly of the general automobile shop were constructed on the eM-Power software platform.

在数字化工厂软件eM-Power的平台上建立了轿车总装车间的底盘工段与分装工段部分工位的仿真对象模型及控制逻辑。

This paper designs application of the algorithm in optimizing multi-objective flexible job-shop scheduling. ( 3) A simulation experiment is carried out to illustrate that the proposed hybrid genetic algorithm could solve the general multi-objective flexible job shop scheduling problem problem effectively.

对该算法在多目标柔性作业车间调度优化的应用进行了详细设计。（3）仿真结果表明，提出的混合遗传算法可以有效解决一般模式下的多目标柔性作业车间调度问题。

The model is evaluated by comparing simulation results to Stirling engine test data, which were obtained from a four cylinder double acting Stirling engine.

结合某型4缸双作用斯特林发动机，开展了发动机的仿真研究和试验研究，研究结果表明，仿真计算的结果与实测值是基本吻合的，从而验证了本文所建立的非线性模型的有效性。

The mathematical model and computer simulation for the movement of the self-acting ball valve in the reciprocating pump

往复泵自动球阀运动规律数学模型及计算

The Simulation Control and Correlation Studies of Electromechanical Valve Actuator

电磁全可变气门的仿真控制及相关研究

This paper introduces the present situation on application of computer simulation in the field of demolition blasting, and outlines the principle of the expert system, the functions of the intelligent system and its application in blasting demolition of chimney, water tower and storied house.

简介了计算机模拟在拆除爆破领域中应用的现状，概述了专家系统的原理、智能系统的功能及其在烟囱、水塔和楼房爆破拆除中的应用。

Numerical Simulation of Supercooled Water Droplets Impingement on Icing Surfaces

过冷水滴撞击结冰表面的数值模拟

Our simulation results show that the proposed scheme can reduce the reserved bandwidth and the blocking ratio when comparing to the tree routing approach.

模拟结果显示，相较于树状架构，所提出之方法具有较低的建置失败率和总预留频宽量。