simulation的例句大全

Prospect of Application of Numerical Simulation Technology to the Casing Pipe Manufacture

数值仿真技术在石油套管制造中应用的展望

Numerical Simulation of 3D Viscous Flow in Exhaust Casing of a Low-Pressure Steam Turbine

低压蒸汽透平排汽缸内能量损失的数值研究

The 3D simulation and recognition method of oil/ water well casing defects

油（水）井套管缺陷的三维模拟及其识别方法

Simulation Method Analysis of On-board Movable Component Based on Absolute Coded Disk

基于绝对码盘的星载可动组件仿真方法分析

Research on motion equation and simulation of NC plane turning lathe

数控车削平面机床的运动方程及仿真研究

For reconstructing the vehicle movement process after collision, the paper considers the factors of accessional brake moment and accessional turning moment and applies kinetics theories to set up two-wheel movement simulation models respectively for braking vehicle and non-braking vehicle.

为了再现汽车碰撞后的运动过程，本文运用运动学理论，在考虑附加惯性矩等因素的作用下，建立了车辆在制动和未制动两种状态下的两车轮运动仿真模型。

Modeling and Control Simulation of Mixture Making Ingredient System with Long Time Delay

大滞后配料系统的建模与控制仿真

Simulation Investigation on Controlling Beam Halo-Chaos Using the Information of Particles in Small Regions

以局部区域内的离子数为探测信息的束晕&混沌控制模拟研究

Numerical simulation on sliding of close joint in rock mass and evaluation on its mechanical behavior

岩体闭合节理摩擦滑动模拟与力学行为研究

Simulation of A Static Bubble Formation Process of Closed Cell Aluminum Foam

静态条件下闭孔泡沫铝气泡形成过程模拟研究

Design and Simulation of 2 DOF Closed Chain Haptic Mechanism

两自由度闭链触觉再现机构的设计与仿真

The simulation result shows that the structure of image matching unit can satisfy the need of the guidance system.

软件仿真结果表明，匹配单元的结构完全能够满足制导系统功能实现的需要。

The obtained curves were analyzed and compared. Finally, using simulation and experimental results to test the multi-functional automatic matching device suction effects and matching effects, the improvement advice will put forward.

最后，用仿真结果和试验结果检验多功能自动配比装置的抽吸效果和配比效果，并进行了改进。

Simulation of the Electromagnetic Stress on the Crack Tip in Metal Carrying Current

载流金属材料裂纹尖端电磁应力的数值模拟

Semi-Physical Virtual Simulation System for Manned Submersible Vehicle and System Performance Analysis

载人潜器半物理虚拟仿真系统及其性能分析

Multiple modules model of 35 kV feed power system normal running fit for digital simulation

35kV馈电系统正常运行数字仿真的多模块模型

Digital Real-time Simulation Model of 35 kV Double-circuit Feed Power System in Normal-operating State

35kV双回馈电系统正常运行数字实时仿真

Cupping ( ductility) value Numerical simulation of cup drawing based on drawing-hole forming technology

基于拉深孔成形技术的杯形件拉深数值模拟

Analyses the effect of frictional coefficient on the zinc-coated sheet process stamping forming by simulate results. ( 3) With combine the finite element simulation and the cupping test to reverse obtained the friction coefficient in process of zinc-coated sheet forming.

随后通过模拟结果分析了摩擦系数对镀锌板的冲压成形影响。（3）运用有限元模拟与杯突试验相结合的方法反求出镀锌板成形过程中的摩擦系数。

To the question of wrinkle and drawing breakage during the rectangle box forming process, this paper describes the simulation of rectangle box deep drawing by Marc finite element analysis software.

针对矩形盒成形过程中各种形式的起皱和拉裂问题，采用MSC.Marc有限元分析软件对矩形盒深拉延成形过程进行模拟。