thicker的例句大全

I'd trust a relative over a friend: blood is thicker than water.

比起朋友来我更信任亲戚: 血浓于水嘛!

Some are flared-that is, thicker at the rim than the center, like a concave lens.

有些呈喇叭形 ─ ─即边缘较中心厚, 类似凹透镜.

Blood is thicker than water, but how did he know you were back?

血浓于水, 但是他是怎么知道你回来了?

We need thicker capital buffers and provisioning coverage ratios.

我们需要更高的资本缓冲和拨备覆盖率.

It can also help convey and activate the plant cells to promote the trunk become thicker.

它也能帮助传达而且刺激植物细胞促进树干变得比较厚.

Some places thicker , some places that are thinner and so forth.

面板有些地方较厚, 有些较薄.

As we ascend the social ladder, viciousness wears a thicker mask.

我们在社会上地位爬得越高, 我们的罪恶戴的面具就越厚.

Thicker films assure fewer asperity contacts and less wear.

油膜越厚,摩擦越少,并且磨损越小.

Microscopically , the aortic atheromatous plaque is thicker than the remaining media at the right.

动脉粥样斑块比右边残存的动脉中膜要厚.

The incoming solar energy is shared by a thicker layer of water.

入射的太阳能被较厚的水层吸收分散.

As the night thicker thicker, its vanishing sluggish.

夜,越来越浓, 如此滞怠地消逝着.

The Monarch Butterfly breathes through its wings and female Monarchs have thicker wing veins.

帝王蝶通过翅膀呼吸,雌性帝王蝶有更加厚实的翅膀脉络.

The thicker lava would have taken two weeks to solidify...

较厚的熔岩需要两周的时间才能凝固。

The beak ravens is much thicker than a crow, Hagoromo more fluffy, especially the throat feathers.

乌鸦的嘴是非常厚比乌鸦, 羽衣更加松软, 尤其是喉咙羽毛.

The plaster became thicker and thicker as the kings sought to outdo each other conspicuous consumption.

各地领主都想在与别的王侯的争奇斗富中胜出,于是,灰泥涂抹得越来越厚,越来越厚.

For a tighter, more secure fit, substitute either thicker laces or cotton laces a rougher surface.

为严格, 更安全的适合, 替代或者较厚花边或棉花花边的粗糙表面.

The thicker pericarp and higher crude fibre content seem to mean a worse performance in tenderness.

较厚的果皮和较高的粗纤维含量似乎意味着较差的柔嫩度表现.

Volumizing shampoos can help give body, and soft perms will make hair appear thicker.

加大香波剂量可有助于头发成形, 轻度烫发可令头发显得厚实.

The more times you pull out the face frame, the thicker it will become.

更时代,你拔出面框, 加厚它将成为.

It is machinable for the thicker of POM.

5、表面塑料层在加工成型时可留一定的余量,装配压入座孔后可自行加工,以达到更好的装配尺寸.