weld的例句大全

The weld repair technology was introduced for crosshead of driven end of Φ 400mm roll. The rolling amount can reach 3.6 × 10~ 4t after the roll repaired.

介绍了Φ400mm轧辊传动端十字头磨损后焊接修补的工艺，修复后轧辊的轧制量能达到36万t。

Dual-Metal Hard Facing Heap Weld Technology of Recovering Hot Forging die

修复热锻模的双金属堆焊技术

Progress in backing weld technology for stainless steel tubes

不锈钢管打底焊接工艺的进展

Investigation into Backing Weld Procedure Technique of All-position Narrow Gap and Thick-walled Pipe Welding

管道全位置焊接打底焊工艺研究

The Development of An All-Position Automatic Welder with STT Technology for Pipe Backing Weld

STT全位置自动打底焊机的研制

Basic flux-cored wire for backing weld to T91 tube was studied in this paper.

研究了用于T91钢管打底焊的碱性渣系药芯焊丝。

Penetrant flaw detection agent was used to detect the backing weld surface, and the number of cracks was indicated by surface crack rate.

打底焊缝正面使用渗透探伤剂探伤，用表面裂纹率表示裂纹的数量。

Indirect Quirk Backing Weld of Thick-walled Vessel

厚壁容器的单面深槽打底焊

This paper describes the reasons for various kinds of defects of backing weld and their recognition on X_rays films It also introduces the protective measures for them

剖析带垫板焊缝中各种缺陷产生的原因及在射线底片上进行辨认的方法，并提出这些缺陷的防止措施

Method for handling weld seam quality of main beam of power plant

电厂大梁焊缝质量的处理办法

The result shows some cracks appearing on vertical weld connecting web plate of body bolster and draft sill as well as the part between web plate of body bolster and top cover plate.

试验结果表明，无中梁罐车存在枕梁腹板与牵引梁立焊缝裂纹及枕梁腹板与枕梁上盖板之间的裂纹。

The results show that the relatively low content of Carbon 、 Manganese 、 Vanadium 、 Boron in deposited metal is a direct cause which promotes formation of ferrite net in weld metal.

结果表明，熔敷金属C、Mn、V、B含量偏低是促使焊缝金属产生网状铁素体的直接原因。

The Development of Carrying Charge Device for Purifying Soot of Weld by Plasma

等离子体净化电焊烟尘装置的研制

Analysis of Weld Property and Temper Brittleness for Cr-Mo Steel

Cr-Mo钢的焊接性和回火脆性分析

In NDT ( Non-destructive Testing ) of weld flaw, UT ( Ultrasonic Testing ) is an important method.

在焊接缺陷的 无损 检测中, 超声检测是一种重要的无损检测方法.

It's possible to weld stainless steel to ordinary steel.

不锈钢是有可能和普通钢焊接在一起的。

If you have been careful when marking out and cutting the parts outlined on page one these parts should all line up accurately ready to weld.

如果你一直小心划出和削减第一页上的这些部分都应该准确地排队准备焊接概述的部分。

When ultimate strength is at 1250~1300 MPa the toughness of the weld is at its maximum.

当焊接强度处于1250～1330MPa之间时,焊缝的韧性最高.

A hole in weld can be detected by feeling for a hot spot on the mold.

一个洞,在焊缝可以侦测到的感觉一个热点在模具上.

Microsoft SQL Server is used as the database of weld process data.

系统采用了Sql Server作为后台数据库来存储和维护焊接工艺数据。