剪的例句大全

These sheep are specially bred for their wool.

这些羊是专为剪取羊毛而饲养的。

There is a live streaming from the Turkish boat.

土耳其船只上有现场视频剪辑。

Influence of Axial Tension on Shear Strength of Reinforced Concrete Restrained Beam

受轴向拉力影响的钢筋砼无腹筋约束梁抗剪能力试验研究

Shearing Stress Problem of Variable Section Round Bar in Axial Tension and Compress

变截面圆杆轴向拉压时的剪应力分析

Influence of shear stress on the ultrasonic measurement of the axial stress of high strength bolts

扭转剪应力对螺栓紧固应力声弹性测量的影响研究

The effect of axial deformation of columns and bending stiffness of connecting beams are taken into account.

本文考虑框架柱子轴向变形的影响和剪力墙之间连梁的作用。

And I will break the bar of damascus, and I will cut off the inhabitant of the valley of Aven and him who holds the scepter from the beth-eden; and the people of Aram will go into captivity unto kir, says jehovah.

我必折断大马色的门闩，剪除亚文平原的居民和伯伊甸掌握权杖的；亚兰人必被掳到吉珥，这是耶和华说的。

Classification of auriferous shear zones and their metallogenic mechanism

含金剪切带的类型划分及成矿机理

Metallogenesis of auriferous shear zone type of gold deposits

含金剪切带型金矿床的成矿作用

The emplacement mechanism of auriferous quartz in the ductile shear zones

韧性剪切带中含金石英脉的就位机制

The Structural Characteristics of Geology in Auriferous Ductile Shear Zone, Huinan, Jilin

吉林省辉南地区含金韧性剪切带的构造地质特征

However, at higher angle of tooth-shaped asperities and under higher normal stress, the failure model II is found, which is in first tension but final shear failure.

在较高的法向应力下，含起伏角较高齿形节理面的非贯通节理岩体可能出现破坏模式II（先张拉后剪切破坏模式）。

First, cut out a long, thin strip of paper.

首先, 剪出一条窄长的纸条.

Not too long. Cut a little off behind and on both sides, too.

不要太长, 后面和两侧也都剪一点.

The cut angle can be adjusted, with very small distortion and high precision.

剪切角可调整, 被减板变形小,精度高.

An Experimental Study on Progressive Failure of Tooth-shaped Asperity Joints in Direct shear

齿形节理渐进破坏直剪试验研究

The shear strength increases with the increasing first-order and second-order asperity heights and normal stress.

节理剪切强度随着一阶和二阶起伏度及法向应力的增大而增大；

There is the displacement function, shear and membrane locking, nonlinear analysis of curved beam element.

综述了系杆拱桥稳定性研究状况,特别分析了曲梁单元形函数选取, 消除剪切与薄膜力闭锁 、 非线性分析的研究进展.

The highest temperature of asperities is much higher than that of worn plane, which is one of the main factors in leading to stress graphitization on worn surface.

摩擦过程中粗糙表面微凸体的最高温度远大于摩擦平面，瞬时的高温和摩擦剪切力的作用使微凸体被应力石墨化。

There are corresponding relations between the deform coefficient and the adjacent tooth distance the saw-tooth chip.

从切屑塑性变形角度分析得出切屑的变形系数与绝热剪切步距的对应关系.