合金的例句大全

Influence of iron as alloying element on crevice corrosion behavior of titanium

合金元素铁对钛缝隙腐蚀性能的影响

The stainless steels and high nickel corrosion resistant alloys are critical engineering materials.

不锈钢和高镍耐蚀合金是重要的耐蚀材料。

Melting and casting rare earth alloy with water cold copper crucible

稀土及其合金熔铸&水冷铜坩埚感应炉

In order to improve the working life of stone crusher hammers, the good and cheap low-alloy steel hammers were successfully developed through a numbers of productive tests and industrial tests.

为提高石料破碎机锤头的使用寿命，经过多次试验摸索和现场工业性试验，成功研制出价廉物美的低合金钢锤头。

Therefore, The applications of this low-alloy bainite cast steel to ore crusher and ore mill can remarkably increase the operational efficiency of these equipments and decrease the processing cost of ore powder.

因此，这种低合金铸钢应用于矿山行业，可明显提高破磨设备运转率，降低矿粉加工成本。

The coarse crystalline LC4 alloy exhibit some superplasticity under lower temperature and higher strain rate, because it can create effective recrystallization refinement.

粗晶LC4合金在较低温度和较高应变速率条件下，因能产生有效的再结晶细化，而呈现出一定的超塑性。

The experimental results of continuous casting of hollow tubes showed that there were many problems such as poor surface quality, too many faults, and coarse crystalline grains in solidification structure and poor uniformity of structure in the circumferential direction.

低熔点的Sn-Pb合金空心管坯连铸模拟实验表明，连铸管坯存在表观质量差、缺陷多、凝固组织晶粒粗大且周向分布均匀性差等问题。

With continuous ball grinding, the powder particle and crystalline grain gradually decreased.

球磨继续进行，合金化的粉末和晶粒不断细化。

Computer Simulation for the Precipitation Mechanism of the Cubic Alloy Including Coherent Strain Energy

包含共格畸变的立方合金沉淀机制的计算机模拟

X-ray diffraction spectrum of L2_1 structure accords with that of face-centered cubic structure; Martensite is body-centered tetragonal structure ( 5M).

合金的母相为L21面心立方结构，马氏体为五层体心四方结构。

RC slab culvert, circular culvert and alloy steel corrugated culvert are applicable to the secular frozen earth area.

钢筋混凝土盖板涵、圆管涵和合金钢波管涵等都适应于多年冻土地区。

Simplified Furnace Burden Calculation for Non-ferrous Alloy Charge The Computer Optimum Burden Calculation for Cast Iron Melted in Cupola Furnace

有色合金炉料质量的简便计算冲天炉熔炼的计算机优化配料

The Effect of Cupola Coke on Improving Quality of Alloy Iron Casting

铸造焦对提高合金铸铁件质量的作用

In many cases of stainless steel cutting operations with carbide tools, a tool life strongly depends on flank notch wear of depth of cut rather than average flank wear of main cutting edge.

硬质合金刀具在不锈钢加工中，其刀具耐用度主要是取决于后刀面边界磨损而不是主切削刃后刀面的平均磨损量。

Only when Sn content in Pb-Ca alloy was more than 0.6wt%, its anodic dissolution of Sn could been observed from cyclic voltammogram and had effect to eliminate the premature capacity loss.

当Pb&Ca合金中锡含量超过0.6%时才可能从循环伏安图观察到锡的阳极溶解，才能起克服早期容量损失的作用。

Influence of Thermal Cycling on Two Way Memory Effect in Cu-Zn-Al Alloy

热循环对Cu－Zn－Al合金双程记忆效应的影响

It is related to the formation of the ( GaP) 1/ ( InP) 1 single layer superlattice in the ordered alloy along [ 111] direction.

认为这与在有序合金中形成沿〔111〕方向的（GSP）1／（InP）1单层超晶格有一定联系。

CO adsorption and coadsorption with O2 on ordered alloy surface Pd { 001} c ( 2 × 2)-Mn were studied with high-resolution electron energy loss spectroscopy ( HREELS) and low energy electron diffraction ( LEED).

用高分辨率电子能量损失谱研究了O2和CO在有序合金表面Pd{θ01}c（2×2）-Ma上的共吸附。

Study on Oxidation and CO Adsorption on Rh ( 100) c ( 2 × 2) Mn Ordered Alloy Surface

Rh（100）c（2×2）Mn表面合金的氧化和吸附CO的研究

Antiphase Domain of an Ordered Alloy

有序合金反相畴研究