弯曲的例句大全

The lower section is left completely flat, only the outer curve being manipulated.

下面一层的裁片要放置完成平整。只将凸的弯曲部位进行缝合。

Making Condition Comparison of Campylobacter Whole Cells Soluble Antigen in ELISA

用于ELISA的弯曲菌全菌混合抗原制备条件的比较

Governing differential equations for the bending response of FGM beams is deduced based on elasticity theory.

基于弹性理论推导了FGM梁弯曲变形的控制方程.

Crocs, according to Kor," are the' poster child "for shoes with a flexible shank.... In other words, on a daily basis, I see patients who come into my office complaining of arch or heel pain and they are wearing Crocs," he said.

据科尔说，洞洞鞋“是腰铁易弯曲的‘典型代表’……也就是说，每天，我都能见到来我办公室抱怨足弓或脚后跟疼痛的病人，他们都穿着洞洞鞋，”他说。

McCloskey secures the Monarch with a bent wire hanger, cutting away the damaged pieces.

麦克洛斯基用弯曲的钢丝衣架固定住蝴蝶，剪下蝴蝶翅膀破损的部分。

Cane is pliable when wet.

藤条潮湿时易弯曲.

Bend over the end piece of the assembly wire opposite the hook.

弯曲装配金属丝与钩型端相对的另一端。

Keeping your lifted leg in the air, bend the leg on the floor slightly and then straighten it again.

保持抬高的腿放在空中，在地板上轻微弯曲腿部，然后再拉直。

The glow starter contains a bi-metallic strip that bends due to heat generated during the initial glow discharge, breaking the circuit and allowing the lamp to light up.

启辉器内含有双金属片，在初始辉光放电过程中产生的热量会使其弯曲，从而断开电路，使灯管得以点亮。

Her neighbor, Jean Merrell, first spotted the bend blades.

他的邻居Jean Merrell首先发现了这些弯曲的刀口。

And a neck with a fretted fingerboard that is usually bent just below the tuning pegs.

一种纵向削制的形状如梨的拨弦乐器，琴颈上有定音档的指板，通常弯曲于调音单轴之。

Aof rubber hose is flexible.

橡皮管可以“弯曲”.

The dynamic characteristic of transmission's bend vibration and torsion vibration was analyzed in this paper.

本文分析了传动系统的弯曲振动及扭转振动的动态特性.

Analysis on Hot Coilbox Bending Roll Control

热卷箱弯曲辊控制浅析

Analysis of Finite Differential Method for Deflection of Box-like Structure with Reinforced Plates

加筋箱形结构弯曲变形的有限差分法分析

He intrigued her. It was the curves of his cheek bones, the confidence in his voice, and the comfort of his warm, steady hands.

他脸颊弯曲的轮廓，他透露着自信的声线，还有他温暖坚实的双手，这一切都让她对他产生了浓厚的兴趣。

According to the criterion, the article examines the cooperative performance of steel plate working together with CFRP and cementing medium by fatigue experiment.

本文参照规范，以应力幅准则为依据，通过疲劳试验检验了胶结在一起的纤维材料和钢板在高次循环弯曲荷载作用下的协同工作性能。

The results show that, the overlying coal-rock mass is integrally bending and sinking, without forming any caving zone and the obvious fault zone.

结果表明，在极薄保护层钻采过程中上覆煤岩体产生整体弯曲下沉，没有冒落带和明显的断裂带。

Working hardening modulus and reverse bend curvature in plate hot roller leveling are different obtained.

加工硬化模量和反弯曲率是中厚板在矫直过程中两个关键且难以确定的参数.

Check that your head is in line with your spine.

检查你的头和脊椎是否已成一直线不要弯曲.