弯曲的例句大全

The dynamic characteristic of transmission's bend vibration and torsion vibration was analyzed in this paper.

本文分析了传动系统的弯曲振动及扭转振动的动态特性.

Aof rubber hose is flexible.

橡皮管可以“弯曲”.

And a neck with a fretted fingerboard that is usually bent just below the tuning pegs.

一种纵向削制的形状如梨的拨弦乐器，琴颈上有定音档的指板，通常弯曲于调音单轴之。

Her neighbor, Jean Merrell, first spotted the bend blades.

他的邻居Jean Merrell首先发现了这些弯曲的刀口。

The glow starter contains a bi-metallic strip that bends due to heat generated during the initial glow discharge, breaking the circuit and allowing the lamp to light up.

启辉器内含有双金属片，在初始辉光放电过程中产生的热量会使其弯曲，从而断开电路，使灯管得以点亮。

Keeping your lifted leg in the air, bend the leg on the floor slightly and then straighten it again.

保持抬高的腿放在空中，在地板上轻微弯曲腿部，然后再拉直。

Bend over the end piece of the assembly wire opposite the hook.

弯曲装配金属丝与钩型端相对的另一端。

Cane is pliable when wet.

藤条潮湿时易弯曲.

McCloskey secures the Monarch with a bent wire hanger, cutting away the damaged pieces.

麦克洛斯基用弯曲的钢丝衣架固定住蝴蝶，剪下蝴蝶翅膀破损的部分。

Crocs, according to Kor," are the' poster child "for shoes with a flexible shank.... In other words, on a daily basis, I see patients who come into my office complaining of arch or heel pain and they are wearing Crocs," he said.

据科尔说，洞洞鞋“是腰铁易弯曲的‘典型代表’……也就是说，每天，我都能见到来我办公室抱怨足弓或脚后跟疼痛的病人，他们都穿着洞洞鞋，”他说。

Governing differential equations for the bending response of FGM beams is deduced based on elasticity theory.

基于弹性理论推导了FGM梁弯曲变形的控制方程.

Making Condition Comparison of Campylobacter Whole Cells Soluble Antigen in ELISA

用于ELISA的弯曲菌全菌混合抗原制备条件的比较

The lower section is left completely flat, only the outer curve being manipulated.

下面一层的裁片要放置完成平整。只将凸的弯曲部位进行缝合。

Transfer printing is a method of applying an image to a curved or uneven surface.

转印是一种将图像印到弯曲或不平整表面的方法.

The effect of shearing on short and thick spindle bending stiffness is discussed.

本文讨论7在计算短、粗主轴弯曲刚度时，剪力时这一刚度的影响，给出了在计算剪切挠度时，剪切变形在空心主轴截面上不均匀分布系数X的近似值；

Is there any bend in the seamount chain?

海山链有弯曲的地方 吗 ?

Semi-hard magnetic 2 J 4 alloy was fabricated via Equal Channel Angular Pressing ( ECAP ).

开发了用等径弯曲通道变形 ( ECAP ) 制备半硬磁2J4合金.

Conclusions: Each method a useful tooldifferent measuring scale and different studying purpose.

结论: 不同根管弯曲度测量法的研究侧重点与观察尺度不尽相同,因而其适用范围也是不同的.

Two series of fatigue crack growth rate ( FCGR) tests using three point bend specimen with different integral knife edge designs are performed. Effect of elastic modulus on the measurement of fatigue crack length using compliance technique is analyzed.

用不同整体刀口设计的三点弯曲SE（B）试样做了两组疲劳裂纹扩展速率（FCGR）试验，分析了弹性模量在柔度法测量疲劳裂纹长度中的影响。

The mechanical analysis on axial bending of pump barrel

有杆泵泵筒的纵向弯曲机理分析