曲的例句大全

Proper sizes of chitin membrane was made and curled into conduit according to the length of defect and diameter, the both ends of the nerve were covered by the conduit by 2 mml;

根据缺损长度及周径裁剪合适长度的甲壳胺膜任其卷曲成管状，神经远、近端各套入2mm；

Study of Thermal Curling Stresses about Cement Concrete Covering of Airport Pavement

机场水泥混凝土加铺层温度翘曲应力研究

When the fibre placement is finished, the tows cover the surface all over, no stacking and detaching.

铺丝完成时，丝束“包裹”整个曲面，无堆叠和分离现象。

Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft.

转动雨刷模组盖，并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。

The facility is operated by the driving of crank to keep a guide rod stable and overwork under high speed, Moreover, it is also available to4 pieces of heald frame according to density.

设备转动通过驱动曲柄来进行，配备导杆不会有颤动、且高速下可以超负荷运转。

Right change& over of the driving crank for typical four-link mechanism

典型四杆机构主动曲柄的正确转向

Dynamic analysis of double crank piston mechanism

双重曲柄活塞机构动力学分析

Analysis of Friction Losses for Double Crank and Connecting Rod Diesel Engine

双曲柄连杆机构柴油机的摩擦损失分析

Modeling and optimization of double crank slide block steering mechanism

双曲柄滑块式转向机构的建模及优化研究

Motion Analysis of the Planetary Gear Drive of the Double Crank Type

双曲柄式行星齿轮传动的运动分析

Application of model 160 double crank camera in strategic range

双曲柄式160摄影机在战略靶场中的应用

Optimized of parameters of basic dimensions of double crank shaft mechanism

双曲柄机构基本尺寸参数的优化

A New Design Method of Double Crank Mechanism

双曲柄机构设计新方法

Crank angle between extreme position effects transmission performances of mechanism in crank-slider mechanism directly.

在曲柄滑块机构中，极位夹角θ的大小直接影响到机构的传动性能。

Research on Transmission Performances of the Crank Angle Between Extreme Position in Crank-slider Mechanism

极位夹角对曲柄滑块机构传动性能影响的研究

Development of Crank Angle 'Window' Controller for IC Engine

内燃机曲轴转角窗口控制器的研制

Each quantity is considered to be a function of the crank angle and radial position in the combustion chamber.

各计算量均作为曲轴转角和燃烧室径向位置的函数；

The transient change of discharge coefficient via engine crank angle is calculated for the first time.

首次计算出连接通道流量系数随曲轴转角的瞬时变化规律。

With the energy analysis to wavelet packet frequency bands, the feature of relative energy of frequency bands can be extracted accurately, which provides the diagnosis of crank bearing wear fault with quantitative foundation.

利用小波包频带能量分析法实现了对信号各频带相对能量信息特征的准确提取，为曲柄轴承磨损故障的识别提供了定量的依据。

This paper focuses on the optimization design of curved stem cranking bar mechanism used single variation parameter ( auxiliary angle) based on the optimum drive angle and maximum itinerary velocity variation coefficient. The method is practical, feasible and can help improve the quality of mechanism design.

利用单变参数（辅助角）按最佳传动角及最大行程速度变化系数对曲柄摇杆机构进行优化设计，提高了机构设计质量，方法实用可行。