材的例句大全

Laser marking is a kind of technique using heat effect of laser to ablate meterials on object surface so as to leave over permanent press.

激光打标是利用激光的热效应烧蚀掉物体表面材料从而留下永久标记的技术。

Behavior of the ablative deformation of resin matrix materials at high temperature

树脂基材料的高温烧蚀变形

Study on the Test of Smoke Signal of Ablative Material

烧蚀材料烟雾信号测试研究

Study on factors affecting ablative performance of c/ c Composites

炭/炭复合材料烧蚀性能影响因素分析

Research and development of ablative performance of C/ C composites

C/C复合材料烧蚀性能的研究进展

In this paper, the study of ablative characteristics of Teflon and a kind of ablator ( AT2) used for the thermal protection system were presented. The study used the means of a CO_2 laser as heating source.

介绍了运用CO2激光加热装置，对聚四氟乙烯（Teflon）和热防护烧蚀材料AT2的烧蚀特性研究。

The flyer design emphasizes conceptually and physically separate functions of light collection at a distance from the laser source, light concentration on the ablator, and autonomous steering.

飞行器草图强调了概念上和物理上各自的功能&从远距离的激光源收集激光、光集中在烧蚀材料上和自主操纵方向。

The microstructure and the ablation process of the phenolic ablator reinforced by fiberglass was studied by means of EPMA, XRF and DTA-TG.

本文采用EMPA、XRF和DTA-TG等现代分析测试手段研究了玻璃纤维增强酚醛型烧蚀材料的显微结构及其烧蚀过程。

Amorphous beryllium hydride, as ablator, can increase conversion from laser to X-rays.

非晶BeH2材料作为烧蚀层，掺入高Z元素后可以提高激光-X光的转换效率。

Study on the microstructure and the ablation process of phenolic ablator reinforced by fiberglass

玻璃纤维增强酚醛型烧蚀材料的显微结构及其烧蚀过程研究

Material research on pipeline of resistance abrading for grinding coal set

磨煤机煤粉管道抗磨弯头材质研究

An method for impact abrasion test, single pendulum scratch method, is introduced and discussed.

本文介绍了用单摆划痕法研究材料冲击磨损性能的实验原理、装置和冲击磨损性能参量。

The Abrasion Test of Cast Wear Resistant Materials in Nitric Acid

铸造耐磨材料在硝酸中的磨粒磨损试验研究

The relative velocity function of the workpiece to the abrasive disk is obtained through kinematic analysis, the material removing function and the lapping uniformity function are deduced based on Preston equation.

在Preston方程基础上，建立了材料去除函数和研磨均匀性函数。

Development and application of advanced composite armor technology

复合材料装甲技术的发展及应用

The prediction of effective thermal conductivity of polymer-based composites is complex.

而聚合物基复合材料的等效导热系数预测比较复杂.

No need of ink, small volume, light weight, compact conformation and 24 hours of continuous service.

无需油墨等耗材, 体积小, 重量轻, 结构紧凑,可24小时连续工作.

Study on the Structures and Materials of a New Bulletproof Composites Armor

新型复合防弹装甲结构材料的研究

Application of efficiency-cost principle in selecting ceramics and designing composite armor

效-费比原则在陶瓷材料选择及复合装甲设计中的运用

The GB/ T 12706-2002 adjusts the thickness of armouring steel tape of power cable, and the thickness of corresponding protective jacket changes too, and material usage reduces correspondingly.

GB/T12706-2002对电力电缆铠装钢带的厚度进行了调整，相应的护套厚度也发生了变化，材料用量相应降低。