温度的例句大全

The finite model of injection molded parts with microstructure region considering latent heat can approximatively forecast the cavity temperature.

采用考虑结晶潜热的微结构件注射成型有限元模型能较准确地预测制品内部温度场分布。

In the scope of temperature the esterification can be regarded as the first order reaction approximatively.

结果表明，在所考察温度范围内反应可看作是假一级反应。

For the aquiferous medium with the same oil content, the volatilization mass is higher and the residual ratio is lower with higher temperature and wind speed.

同种条件下，含油量越高，油品在介质中的残留率越高，对于同一含油率的含水介质，温度和风速越高，挥发量越高，介质中油品残留率越低。

Experimental results showed that optimum temperature for the growth of M. arenaria was 29 ℃, but screening tests could be carried out between 25 to 33 ℃.

are（？）ia在紫花苜蓿上的最适发病温度为29℃，但抗病性鉴定筛选可在25～33℃之间进行。

ST of Palm and BVP of fingers can be the sensitive parameters reflecting emotional arousal level of sailors.

手掌心温度和手指端血容可以作为帆船帆板运动员情绪唤醒水平的敏感性监测指标；

The main causes that resulted in the piers seriously cracking were inadequate arrangement of pier reinforcement, over-temperature-stress of the piers and higher values of static ice pressures.

闸墩配筋量明显不足、闸墩温度应力超限和静冰压力过大，是引起闸墩严重开裂的一些主要原因。

Study on the hatching temperature traits of Chinese Artemia eggs

中国卤虫卵孵化温度特性的研究

The thermal conductivity of heat insulation materials, containing vacuum rubber board, asbestos board and quartz glass etc. was tested at different average temperature with RDL 1 automatic measuring apparatus made by ourselves.

用自行设计的RDL-1型物质热导率自动检测仪测试了真空橡胶板、石棉板等材料在不同温度下的热导率；

Storage temperature, light and package materials obviously affected the color stability of green asparagus juice during storage time.

贮藏温度、光照和产品包装材料对芦笋汁色泽稳定性产生很大影响。

The quality change of asparagus juice during storage were a close relation to temperature.

芦笋汁在贮藏过程中的质量变化与温度密切相关。

Analysis of asphalt pavements temperatuer stress with asphalt treated base course

沥青稳定碎石基层沥青路面结构温度应力分析

Tests on thermal stress in asphalt cement sample and its numerical simulation

沥青混凝土温度应力试验及其数值模拟

Based on the present research productions, Load stress and temperature stress of asphalt pavement with lean concrete base are additionally calculated and the influence of correlated factors is analyzed.

在现有研究成果基础上，补充计算了贫混凝土基层沥青路面的荷载应力和温度应力，并分析了各因素的影响。

Annealing: Heating to 780 ~850 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至780～850℃,在此温度停留1～3小时, 在炉中冷却.

At sufficiently high temperatures considerable number of electrons are able to escape.

温度足够高时,就有大量电子逸出.

Adoptshigh-precious temperature controlling system multi-functional operation penal. Easy to operateindicate the machine running condition.

采用精密电子温度控制和多功能面板,操作方便,可及时显示机器运行状况.

The heat carrying agent transportation is the key link in the biological fuel oil production process.

热载体输送是生物燃油生产过程中的关键环节,输送过程中温度与输送量直接影响生物燃油的生产.

Annealing: Heating to 750～780℃ , Holding time 1～3 h, Colding in furnace.

退火: 加热至750～850℃, 在此温度停留1～3小时,在炉中冷却.

Annealing: Heating to 800 ~850 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至800～850℃,在此温度停留1～3小时, 在炉中冷却.

Annealing: Heating to 830 ~880 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至830～880℃,在此温度停留1～3小时, 在炉中冷却.