熔的例句大全

A New High Voltage Dropout Fuse with Current Limiting Characteristics

一种具有限流特性的新型跌落式高压熔断器

The curve of heat release rate and mass loss rate had the same shape which showed that irradiation cross-linking had the effect in the condense phase. The char formed after cone calorimetric test had the wrinkle structure to wrap the melt drops.

锥形量热仪测试的热释放速率和质量损失速率曲线轮廓类似，也说明了辐照交联在凝聚相起到的作用；燃烧后炭层呈褶皱状结构，有利于对熔滴的包覆。

The extraction separation experiment and differential scanning calorimetric measurement indicate that the resultant belongs to crystallizable isotactic polymer, possessing isotactic index ranging from 45% to 90%, melting point 215 ℃ and Vicat softening point 193 ℃.

抽提分离和差示扫描量热法测试表明，其为结晶型全同立构聚合物，全同立构含量为45%~90%，熔点为215℃，维卡软化点为193℃。

The closely spatial relationship between metasediments, migmatites and migmatitic granite-gneiss in the district exhibits the entire process of transformation from sediments to granitic rocks by metamorphic differentiation, migmatization and partial melting.

变沉积岩、混合岩及混合花岗片麻岩在空间上的密切共生关系，揭示了沉积物经历了变质分异、混合岩化和部分熔融作用改造成花岗质岩石的过程。

The line is composed of hot gas generator , melting furnace and annealing furnace in series.

研制成功一种新型烧煤的炉组,由热煤气炉 、 熔化炉和退火炉串联组成.

Wireless hot-melt Adhesive binding and hot set belongs to the contra te line.

无线胶粘装订和热熔线烫订属于端面粘结.

The medium-frequency induction furnace melting process of the synthetic as-cast ferrite nodular cast iron was described.

概述用中频感应电炉熔炼合成铸态铁素体球铁的生产工艺.

In order to solve the problems of refractory metal oxide and carbide inhomogeneous distribute in C/ C composites. In this paper, three kinds of zirconium doped C/ C composites were prepared by different materials and processes.

为解决难熔金属氧化物、碳化物在C／C复合材料中的分布的问题，本文以不同原料和工艺制备出3种锆掺杂C／C复合材料。

Oxidation Resistance of Chromium Carbide Coating by Molten Slag Method

熔渣法碳化铬涂层的抗氧化性能研究

Performance Investigation of Biomass Gasification-Molten Carbonate Fuel Cell Combined Cycle Power Generation System

生物质气化–熔融碳酸盐燃料电池联合循环发电系统性能研究

The sprue sections influence the technological yield of small castings in investment casting.

对于小型熔模铸件，直浇道的截面形状将影响其工艺出品率。

Numerical Simulation of Mold Filling and Solidification and Experimental Analysis in Furnace Grate Investment Castings

炉排片熔模铸造充型与凝固过程的数值模拟及验证

The team have to seek the rare opportunity to see into its molten heart.

队伍不得不寻求难得的机会以看到其熔融的心。

Techniques of Applying Three-Coat Melting Epoxy Powder to Steel Pipe Piles

钢管桩三层熔结环氧粉末涂敷技术

Aluminium electrodeposition from the organic electrolytic systems of ether solvents, aromatic hydrocarbons and dimethylsulfone have been mainly introduced.

着重介绍了在有机醚溶剂、芳香族碳氢化合物、乙基磺酸脂等有机熔盐中铝的电沉积情况；

Strength checking calculation of partial penetrated butt weld in the box component

箱形钢构件半熔透对接焊缝的强度验算

The results showed that the calculated depth of base, top width and spiral angle of flight at the start and end of the melting zone for extruder screw were in or close to the ranges recommended in literatures

结果表明，计算所得熔融段起、末端的螺槽深度、螺纹顶宽度和螺纹升角均位于或接近文献中所建议的最佳取值范围

Expose cylinders to corrosive materials such as ice melting compounds.

把钢瓶暴露于腐蚀性材料,如冰熔化的化合物.

AIF _ 3— Al _ 2 O _ 3 ( sat. ) melts at 1000℃ by a steady state potentiostatic method.

用稳态恒电位法及脉冲技术,对1000℃下2.7NaF·AlF_3-Al_2O_3 ( 饱和 ) 熔体中SnO_ 2基情性阳极上氧析出的超电压作了测定.

Fig. 5 The effect of heat input on the average grain size of α-Mg in FZ.

图5线能量与熔合区中平均晶粒尺寸的关系.