符合的例句大全

This document is intended for students through life Surveys and results analysis, vocational schools provide a richer, more scientific, in line with the actual life of the students in vocational education implementation strategies.

本文意图通过对学生生命观的调查与结果分析，为中职学校提供更为丰富、更为科学的、符合中职学生实际的生命教育实施策略。

In all collected papers scheme, will be accord with the overall interests of the human species on earth feasible scheme.

在所有征集到的论文方案中，也一定会有符合地球人类整体利益的可行方案。

The ballistic curve prediction provides guidance for choosing centroid of test model, and the computational results coincide with tests very well.

弹道曲线的预测为航行器试验模型质心位置选取提供了依据，计算结果与试验符合良好。

The invalid incorporation system refers to through litigation to take order with the company which does not conform to the fundamental provisions of corporation law in the process of set-up.

公司设立无效是指对已成立的公司在其设立过程中有不符合公司法规定的根本性条件的情形，通过诉讼予以处理的措施和制度。

The each single effect of N, P and W on yield increasing was statistically significant and coincided with the law of diminishing return.

而供水充足时，N肥对产量的影响作用更敏感.N、P、W3个单因素对春小麦均有明显的增产作用，而且符合报酬递减率。

Check if the voltage indicated on the bottom of the appliance corresponds to the local mains voltage before you connect the appliance.

检查，是否电压在器械的底部上指出符合当地的输电干线电压在你连接器械之前。

Are controlled final verification instructions used to insure inspections and test are completed and product in conformance prior to shipping?

在装运前有否受控的最终检验规程来确保产品已经行检验和测试并符合要求？

At the time of delivery, this packaging must be bear labels in conformity with the legal stipulations in force.

交货时，该包装必须具有符合有效法律规定的标签。

With the maximization of ship, the competition of the world container pivot harbor is fiercer, on one hand ultra and large-scale container ship can only berth port, which condition of depth of water, efficiency of load and unload and management level is qualified;

船舶的大型化使得世界集装箱枢纽港的竞争更加激烈，一方面超大型的集装箱船舶只能停泊在水深条件、装卸效率和管理水平符合要求的港口；

Results Positive rate of the biopsy specimen was 56.9% and the correlation rate with operations was 91.6%.

结果穿刺阳性率56.9%，穿刺诊断与手术诊断符合率91.6%。

Tween 20 can be used as inhibitor for zinc electrode due to its blanketing effect, which is favorable to corrosion inhibition. The adsorption behavior of Tween 20 on surface of zinc electrode is in accordance with the Freundlich isothermal equation.

吐温20对锌电极具有一定的缓蚀作用，其缓蚀作用主要是由于覆盖效应，吐温20对锌电极在锌电极表面的吸附行为符合Freundlich等温式。

If rejected, the batch shall be replaced at Blender's expense with Blended Product meeting PetroChina's specifications.

若被拒收，则该批产品必须以符合中国石油规格的调和产品予以调换，有关费用由调和方承担。

The blood concentration/ time data from single intravenous bolus injection of 6 mg/ kg were adequately described by a linear three-compartment open model.

一次快速iv6mg/kg后的血药&时间过程符合线性三室开模型。

It is found from experimental investigations on the distortion of ferromagnetic resonance curve and the broadening fo the resonance linewidth due to amplitude modulation that the relationship between apparent linewidth and true linewidth is in agreement with Wahlquist equation [ 1], when small modulation condition is satisfied.

本文通过调制幅度引起铁磁共振曲线畸变和使共振线宽增加的实验研究，发现满足小调制条件时，视在线宽和真实线宽的关系符合文献[1]所提出的方程式。

Through analyzing the temperature field and stress field of typical steel castings some casting parameters as modulus, the distance of feeding head, cold iron are validated and modified, which is in accordance with the production-lines.

通过选取典型的铸钢件，采用实验的方法，对温度场、应力场、模数、冒口补缩距离、外冷铁等铸造工艺参数进行验证并加以修改，使其符合生产实际。

The paper has given relations between holding current and temperatures from 25 ℃ to 300 ℃ range. The experiment results are essential agreement with the model that the paper has given.

文章给出了这两种模式下的维持电流与温度关系，公式在25℃至300℃之间能与实验结果符合。

And calculated breech pressure, muzzle velocity and discharge parameters agree with experimental results.

同时，计算的膛压、初速、放电参数与实验基本符合。

Mean While, loading force provided by the force loading maintainer has been compared with the actual breech pressure, and the method which more in line with practical gun pressure has been put forward.

同时，将动力加载机构提供的加载力与实际膛内压力进行对比，提出了使其更加符合实际膛压的方法。

With the system we have designed and machined the broaching tool that has used to machine slippage gears in the gearbox of tractor.

应用该系统设计制造了拖拉机变速箱滑移齿轮花键孔拉刀并进行了加工实践，使用结果表明：被加工齿轮花键孔参数符合设计要求。

Near-perfect theoretical agreement with experiment was achieved.

理论与实验达到了近乎完美的符合一致.