When the bar is released, the cams flare outward and wedge into place, providing protection.

The Cams were different, and so he liked it here.

曹家的人是个例外, 所以他喜欢在这儿.

The measurement and error evaluation of cams in CNC measuring center is researched in this paper.

研究了直接在CNC齿轮测量中心上检测凸轮并评定误差的方法和理论.

Cylinder graduation-groove-cam is a kind of daily cam in the pattern of many kinds of cams.

圆柱分度槽凸轮是多种凸轮型式中的一种常用凸轮.

There are nanny cams hidden throughout this entire house. All right?

房子里安了很多隐蔽的摄像头懂 吗 ?

The measurement and error evaluation of cams in 3-coordinate measuring machine is researched in this paper.

本文研究直接在三坐标测量机上检测凸轮并评定误差的方法和理论.

Lubricates guide bolts asas guiding cams.

润滑导螺栓和导凸轮.

Substitutes damaged guide bolts and cams.

替换损坏导螺栓和导凸轮.

Angular velocity grinding and linear velocity grinding are the main grinding method for camshaft.

工件恒角速度磨削和工件恒线速度磨削是目前精加工凸轮轴的主要磨削加工工艺.

The opening of each valve is controlled by a camshaft.

每个阀门的开启由凸轮轴控制.

These engines are known as dual overhead camshaft ( DOHC ) engines.

这些发动机被称为双顶置凸轮轴 ( DOHC ) 发动机.

Since 1958, an engine with a single overhead camshaft has been used.

从1958年起, 便已使用带有单顶置凸轮机的发动机.

Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.

拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条.

This means that the crankshaft will make two revolutions for every revolution of the camshaft.

这意味着凸轮轴每旋转一次曲轴将旋转两次.

Argon arc remelting hardening is a new technology of manufacturing camshaft.

氩弧重熔硬化是生产凸轮轴新工艺.

Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.

顶置凸轮, 链条传动, 正时配气系统传动平稳,噪音小.

In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.

详细分析了摇架式凸轮轴磨床凸轮轮廓的数控成形原理.

A camshaft driven by a chain or belt turns in the same direction as the crankshaft.

凸轮轴被链或者带驱动,使其朝着曲轴相同的方向转动.

The camshaft has a cam, on which there is a lob , or bump.

凸轮轴上有一个凸轮, 凸轮上有一个凸角.

The ratio of the crankshaft to the revolutions of the camshaft is 2∶1.

曲轴的转速与凸轮轴的转速之比是2∶1.

The camshaft and crankshaft gears can be connected directly, or meshed.

凸轮轴和曲轴齿轮可能被直接连结, 或者相啮合.