Therefore, the finite element method was used in this article to systematically study the Interference technology of the crankshaft gear.

Fault Diagnosis of Crankshaft Main Journal Grinder Based on Vibration Technique

基于振动诊断技术的曲轴主轴颈磨床故障诊断

Design of Wheel Dressing Program for 4R Crankshaft Grinder

4R曲轴磨床砂轮修整程序设计

Synchronous Control for Crankshaft Grinder Head-tail Stock Based on AC Servo

基于交流伺服驱动的曲轴磨床头尾架同步控制方法

Refitting Toyoda Crankshaft Grinder with Siemens 840D

用西门子840D系统改造丰田七砂轮曲轴磨床

By the modal experimental of the crankshaft, the validity of the finite element model about crankshaft which includes pulley and flywheel was verified.

通过曲轴的模态试验验证了曲轴有限元模型的准确性。

The models of crankshaft with flywheel and pulley and crankshaft without flywheel and pulley were analyzed and compared.

对曲轴带飞轮和皮带轮及不带飞轮和皮带轮两种情况下进行了模态分析，并进行了比较。

Fit the crankshaft belt pulley with a helper.

与一个助手装配曲轴皮带轮。

Water pump and cooling fan of traditional cars are usually driven by the engine through V belt, which is intertwined between crankshaft pulley and water pump pulley. Therefore, the rotational speed of water pump is in proportional relationship with the engine speed.

而传统汽车的水泵和散热风扇一般由发动机曲轴通过V带传动，传动带环绕在曲轴带轮与水泵带轮之间，因此水泵转速与发动机转速成比例关系。

The engine number can be found on the front right of the crankcase next to the crankshaft pulley.

可以在曲轴皮带轮旁边的曲轴箱右前方找到发动机号。

Our products mainly include crankshaft pulley, water pump pulley, air-conditioner pulley and electric motor pulley, tensioner pulley, damping pulley, Idler assy pulley.

曲轴皮带轮、水泵皮带轮、空调皮带轮、电机皮带轮、张紧轮、减震皮带轮及怠速轮的生产及安装。

Only turn engine using the crankshaft pulley, not at the camshafts.

仅能使用曲轴皮带轮转动发动机，而不是在凸轮轴处转动。

A Crankshaft Fluctuation Sensor ( CKF) is located near the bottom of the timing cover where it generates a signal as the crankshaft timing chain sprocket rotates past it.

曲轴位置传感器安装在定时器壳底部附近，产生一个曲轴定时链轮齿通过的信号。

A drive system for an internal combustion engine including an endless chain connecting a drive sprocket on a crankshaft to a driven sprocket on a camshaft.

一种用于内燃机的驱动系统，包括将曲轴上的主动链轮连接到凸轮轴上的从动链轮的一条环链。

Put on chain between crankshaft drive sprocket and intermediate shaft drive sprocket.

安装曲轴传动链轮和中间轴传动链轮之间的链条。

This paper introduces the principle and method of the holding control for automatic charging and plunger chip, which is realized by using proximity switch to test the motion of crankshaft of punch press, and velay or SCR to control clutch through electromagnet.

本文介绍了利用接近开关检测冲床曲轴动作，利用继电器和可控硅通过电磁铁控制离合器吸合动作，从而实现冲床自动送料动作和冲头动作同步控制的原理及方法。

Equilibrium analysis on crankshaft's rotation inertia force of internal combustion engines

内燃机旋转惯性力的平衡分析

The second injection pump drive and installation, the secord injector arrangement, the cylinder head and rocker arm support modifications are described in detail, as well as the installation of crankshaft rotation angle grating disc which is necessity for combustion research in cylinder pressure sensor.

详细论述了喷油泵的安装和驱动、喷油器的布置、气缸盖和摇臂座的改造以及气缸压力传感器、曲轴转角信号光栅盘轴的安装。

The conclusion from the analysis points out that the effective way to raise the productivity of this series of looms, while maintaining the same shuttle speed and low power consumption, is to increase the angle of crankshaft rotation available for the passage of the shuttle.

文章从分析得出结论：从既提高生产率，又维持棱速不变，并保持较低的功率消耗来看，唯一有效的措施是进一步扩大梭子越过梭道的时间角度。

The output for diesel engine is proportional to the product of crankshaft rotation speed and injection pump rack displacement from fuel supply starting point. Injection pump rack displacement influences diesel engine rotation stability and locomotive tractive characteristic.

柴油机输出功率的大小跟曲轴转速与喷油泵齿条由供油始点开始的位移量乘积成正比，喷油泵齿条位移量影响柴油机运转的稳定性和机车的牵引特性。

Counter crankshaft rotation The steering wheel is mounted on a steering shaft that extends into the steering gear.

反曲轴转动方向的转动转向盘安装在转向轴上，转向轴延伸至转向器。