alloy的例句大全

Study on Crystallization Process and Microstructure of Ti-Si Eutectic Alloy Systems

钛硅共晶系合金结晶过程与微观形貌

Influence of side ultrasonic treatment on solidification characterization of Al-Si eutectic alloy

侧部导入超声处理对共晶Al-Si合金凝固特性的影响

Eutectic furnace is a special equipment based on the eutectic principle, packaging chip according to different eutectic technological requirements of welding alloy materials under a vacuum or inert gas protection environment.

共晶炉就是基于共晶原理开发的专用设备，在真空或惰性保护气体环境中按照不同焊接合金材料的共晶工艺要求，完成芯片的封装。

The results show that when Al content is 4.25%, the graphite content is high, the eutectic graphite is the main morphology and the matrix of the alloy is single γ-Ni ( Al) solution.

结果表明：当Al含量为4.25%时，凝固组织中的石墨含量较高，且以共晶石墨形态为主，基体为单相-γNi（Al）；

According to the results of DSC and microstructure analysis, the more Al content, the higher melting point of the alloy, but the more α phase dendrites, the less eutectic cementite.

从差示扫描量热分析和显微组织得出：随含铝量的增加，合金的熔点提高，α相枝晶增多，晶间的共晶体减少。

Eutectic Structure of Binary Mg Li Alloy During Directional Solidification

定向凝固条件下二元Mg-Li合金共晶组织的研究

Superplastic Treatment and Application of Cast Zn-Al Eutectoid Alloy

铸造锌铝共析合金的超塑性处理及应用

Besides, alloy steels containing elements which move eutectoid point to the left in Fe-C equilibrium diagram are also suitable for magnetic field quenching.

对于合金钢，凡是含有能使Fe-C状态图共析点左移的合金元素的钢均适用磁场淬火工艺。

Experiment and Research on Die Casting Technique of Textile Spindle Base Made of ZA-27 Alloy

ZA-27纺锭锭底压铸工艺的试验研究

The Research of Powder Release Agent for Aluminum Alloy Vacuum Die casting

铝合金真空压铸用粉状脱模剂的研究

Study of vacuum die casting process of aluminum alloy automotive steering gear housing

铝合金汽车转向器壳体真空压铸工艺研究

Technical features of 33 MW flue gas expander and the selection of high temperature alloy material

33MW烟气轮机的技术特点及高温合金材料选用

This essay get breakthrough in the study of lining, new type high-temperature wearable alloy and parts and the soft start shaft coupling of centrifugal air exhauster changing in the tail of kiln.

本文在对内衬的技术研究开发、新型高温抗磨合金及其高温抗磨件开发研制、窑尾排风机软启动联轴器的设计发明与应用等方面取得了重大突破。

A study on vacuum evaporated decorative film of Ti-Cr alloy

蒸镀铬钛合金装饰膜的研究

Vacuum evaporated film of Ti-Cr alloy has been studied.

利用物理气相沉积（PVD）真空蒸镀法，研究铬钛合金装饰膜。

Characteristics of internal friction and modulus associated with non-equilibrium diffusion-type phase transformation in eutectoid Al-Zn alloy

共析Al-Zn合金非平衡扩散型相变内耗和模量特征

The Study of Superplastic Mechanism of Zn-Al Eutectoid Alloy

Zn－Al共析合金室温超塑性变形机理

Usually, excellent Superplasticity of Zn-Al eutectoid alloy could be obtained by pre-deformation ( rolling or forging).

锌铝共析合金具有良好的超塑性，但通常需要经过预变形（轧制或锻压）来得到。

A Study of m-c-δ( or m-k-δ) Relations of Superplastic Zn-22% Al Eutectoid Alloy

Zn-22%Al合金超塑性的m-C-δ（或m-k-δ）关系的研究

The experimental results showed that the microstructure of Cu 26.6wt% Mn alloy changed from cellular to dendrite, super fine cellular and segregation free solid with the increase of growth rate;

实验结果表明，重熔区组织较基体组织大大细化；随着生长速度的增大，Cu26.6wt%Mn合金的组织由低速胞晶向枝晶、高速胞晶及完全无偏析固溶体转变。