seam的例句大全

Study on bacterial and virus fossils from a smelly coal seam in southeastern Shanxi

晋东南地区臭煤层中细菌化石及病毒化石的研究

These annotations enable a bidirectional flow of variables between the view template and Seam components.

这些注释使变量能够在视图模板和Seam组件之间双向流动。

The Application of Panoramic Borehole Camera to Extremely Thick Seam Working Face in Carboniferous System

钻孔摄像技术在石炭系特厚煤层工作面的应用

The coal seams were crossed frequently in the construction of Tianchi Coal Mine airshaft, and the gas content was great. The occurrence of coal seam situation was grasped by using borehole surveying and geologic column.

针对天池矿回风立井井筒施工中频繁揭穿煤层并且瓦斯含量较大的情况，通过打钻探煤结合地质柱状图准确掌握煤层的赋存情况；

The alloy element action and brazed seam structure are analyzed.

分析了钎料各合金元素的作用及钎缝组织。

Cut through the brazed seam on the connection to the side section with the parting grinder.

用分离打磨机切断连接到侧面部件的铜焊缝。

Further research shows that element Mg in 6063 is the main cause making the flux ineffective and the quality of brazed seam degraded.

进一步的研究指出：6063铝合金中的合金元素Mg是使钎剂失效和恶化钎缝质量的主要原因。

The results suggest the joint is not ideal if the Cu layer is too thin or too thick, and it is very important for existing some eutectic substance in brazed seam.

研究表明，Cu层的厚度太薄或者太厚，其连接效果都很不理想，同时在Al合金与Cu中间层接触反应钎焊中，钎缝区存在适当的液相对于提高接头强度是至关重要的。

The simulation mentioned above was confirmed by series experiments, and the proper thickness of the brazed seam is 50~ 80 μ m for the CRB joint of Al with Si as an interlayer.

在试验证明FEM计算结果的可靠性的基础上，给出了Si为中间层进行LF21铝合金接触反应钎焊时，其合适的钎缝宽度范围是50～80μm。

The brazing-ability and quality of brazed seam of 6063 aluminum alloy brazed by Al-Si eutectic filler metal and QF flux is discussed by means of test of spread-ability and test of T joint.

本文用平百铺展试验和T型接头试验，研究了6063铝合金采用AI－St钎料和氟化物钎剂（QF钎剂）钎焊时的钎焊性和钎缝质量。

The Al element in the substrate diffuses into the brazing seam, forming a thin reaction layer in the interface region.

焊接母材中的Al元素向焊缝发生了扩散，在界面区形成了一层很薄的反应层。

Effects of Heat Treatment on Properties of Brazing Seam

热处理对硬钎焊焊缝性能的影响

A new method to improve the heat resistance of the brazing seam

提高钎缝耐热性的新途径

X ray image analysis of high temperature brazing seam for corrugated plate sandwich structure

波纹板夹层结构高温钎焊焊缝X射线影像分析

Effect of alloy powder on Microstructure of brazing seam

钎缝中合金粉对组织的影响

The welding residual stresses exist mainly within 15 mm from the brazing seam.

焊接残余应力主要分布在离钎缝15mm以内的区域。

The Study of Varied Thickness of Coal Seam Using MCNP Method in the Coal Quality Analysis Experiment by Neutron

中子煤质分析实验中应用蒙特卡罗模拟方法进行煤层厚度变化的研究

Repeat this procedure at the finish of the seam.

在终端重复这道程序.

The logistic arm must seam lessly deliver material as needed.

后勤部队必须及时输送所需物资.

The height of the watering fissures is 21.5m because the height of caving zone is about 10m after the mining of all the 3 seam ( 4 layers), and the result basically accord to the result of theoretic calculating and numerical simulation;

3煤层全采后（4个分层）垮落带高度为10m左右，导水裂隙带的高度为21.5m，与理论计算和数值模拟结果基本一致；