拧的例句大全

A Christmas Cracker is a cardboard paper tube, wrapped in brightly coloured paper and twisted at both ends.

圣诞拉炮是用硬纸板做的纸筒，再用色彩鲜艳的彩纸包裹在外面，两端拧紧。

Everything was jammed into the tightest cases, fitted into the narrowest corners, fenced up behind the most impertinent cushions, and screwed into the acutest angles, to prevent its philosophical composure from being disturbed by the rolling of the sea.

每一件东西都被塞进最紧凑的箱子中，装到最狭窄的角落里，后面用最不得当的软垫防护着，并用螺丝拧紧到最尖锐的角中，以防止它那像哲学家般的沉着镇静被海洋的滚滚波涛所扰乱。

The hexagonal bolt goes through the anti-receding expansion pipe and is screwed in the expansion pipe.

一六角螺栓，可穿过防退膨胀管，拧入膨胀管；

Remove the shower head and place a chicken bouillon cube in it, then put the head back on.

卸下淋浴龙头，在水管里放块鸡汤调味料，再把龙头拧回去。

The handle has become loose , so screw up it, please.

把手松了, 请用螺丝拧紧.

Can you screw up this handle for me?

你能帮我把这个把手拧紧 吗 ?

When cleaning, open liquid receiver, add clean water, and screw up bung.

进行清洗作业时, 打开贮液桶, 加入清洁水, 拧紧桶盖.

You have to screw up the handle, it has become loose.

柄松动了,你得把螺丝拧紧.

The plumber took out a wrench and tightened the bolt.

管子工拿出一把扳手拧紧了螺栓.

Tighten adjustment screw to 3 N & middot; m ( 30 in-lbs ) torque.

拧紧调整螺丝到3N· m ( 30in-lbs ) 扭力.

Tighten glass track nuts to 6 N & middot; m ( in-lbs ) torque.

拧紧玻璃轨道螺帽至6N & middot; m ( in -lbs ) 扭力.

Tighten the camshaft housing screws in the sequence shown.

按照所示顺序，拧紧凸轮轴室螺钉。

Refer to tools and tightening torques in chapter" removing camshaft housing"!

参阅章节“拆卸凸轮轴室”中的工具和拧紧力矩！

Tighten central screws on the sprocket and camshaft controller to the prescribed final torque using a torque angle wrench.

用扭力角度扳手将链轮和凸轮轴控制器上的中央螺钉拧紧至规定的最终力矩。

Install the serpentine drive belt and tighten to obtain the specified tension.

安装蛇形驱动带,拧紧到规定的张力.

Supple suede , bends or twists with agility.

软山羊皮)、能够灵活地弯或拧的东西.

Adie pulls her hair back and twists it into a knot.

爱狄将头发往后一拢，拧几下，打了个结。

The design of bolt-screwing device for installing a robot on the lighting rod on air bracket grounding wire

高架地线上避雷针安装机器人螺栓拧紧机构的设计

B. Install the door closer and screw down all the screws.

安装闭门器主体并拧紧螺丝.

LOD distances tweaked on certain objects.

在一些物体上的LOD距离拧的问题?