曲的例句大全

Bispectrum Analysis for Vibration Data of Crankshaft Bearing in Diesel Engine

柴油发动机曲轴轴承振动信号的双谱分析

Special Knockout for Engine Crankshaft Bearing of Motorcycle

摩托车发动机曲轴轴承专用拆卸工具

Research For Improvement on Crankshaft Bearing Lubrication of IC Engine

改善内燃机曲轴轴承润滑状态的研究

Control of Positional Accuracy for Keyways in Crankshaft Timing Gear Journals

曲轴齿轮轴颈键槽位置精度控制方法

The study showed that the structural dimensions played an important role the crankshaft gear stress. Based on these, on analyze the impact law of the structural dimensions affect to the interference fit was mainly focused.

研究表明结构尺寸对曲轴齿轮应力影响较大，在此基础上着重分析了结构尺寸对过盈量的影响规律。

The primary drive gear ( crankshaft gear) and the primary driven gear are the source of noise due to their high speed and bigger reduction ratio.

作为摩托车初级传动的曲轴齿轮及初级从动齿轮，由于转速高及降速比大，是产生噪声的主要因素。

The relation between the related structural dimensions of interference fit, the contact state, the running state and the crankshaft gear stress was mainly investigated.

重点探讨了过盈联接相关结构尺寸、接触状态以及运转状态等因素与曲轴齿轮应力的关系。

Therefore, the finite element method was used in this article to systematically study the Interference technology of the crankshaft gear.

为此本文利用有限元方法，对曲轴齿轮过盈联接技术展开了系统的研究。

The drive mechanism includes a two-grade reducing mechanism, flywheel energy-storing mechanism and crank drive mechanism;

其中传动机构包括二级减速机构、飞轮储能机构和曲轴传动机构；

A low cost microcomputer closed loop control system of crank shaft processing

经济型微机闭环曲轴加工控制系统的研制

Rotating speed adjusting by numerical control on special crank milling machine

专用曲轴铣床旋转调速的数控实现

A microcomputer numerical control system for crank machining

开环补偿、闭环控制曲轴加工微机数控系统

Analysis of Servo Control of the Crank Press Driven by Hybrid Excitation Brushless DC Motor

基于混合励磁直流无刷电机的曲柄压力机伺服控制分析

It consists of four main parts: external gear, internal gear, control board and crank.

该装置由内齿轮、外齿轮、控制板及曲轴四个主要零件组成。

The crank drive must not become jammed.

曲柄传动绝不能卡住。

If parts of the crank drive were replaced, you must determine the new cylinder-head gasket again by measuring the piston projection in "tdc" position.

如果曲柄传动的零件已更换，则必须测量活塞在“tdc”位置的突出部分以重新确定新的气缸垫是否恰当。

On the basis of the discussion on the principle of double crank ring-plate-type cycloid drive, the method of force analysis is proposed, and the accurate model of force analysis established.

在论述双曲柄环板式针摆行星传动原理的基础上，提出了受力分析方法，建立了准确的力分析模型。

On parametric feature lib of internal combustion engine crank gear

内燃机曲柄连杆机构参数化特征库研究

Special Milling Machine for Crank Gear of Pumping Units

抽油机曲柄齿专用铣床

Principle and Application of the Additional Weight Balance of Micro-amplitude Mechanism Driven by a Crank Gear

曲柄机构传动的微幅振动机械的配重平衡平衡重，配重作为一种抗衡的重量