gasket的例句大全

Moto parts major in Iveco fitting , C . V boot , flasher , Distributor cap, Gasket and so on.

汽配方面主要有白金 、 防尘套 、 闪光器 、 汽缸垫等.

Bonnet joint varies from flat face gasket-joint to ring-type bonnet joint, depending on class.

阀盖连接方式从平面垫圈连接到环形阀盖连接, 压力等级不同,连接方式也有所不同.

Elastic adhesive felt after milling can be used as shock, seal, gasket and flexible steel needle felt cloth base material.

缩绒粘合后毛毡富有弹性，可作为防震、密封、衬垫和弹性钢丝针布底毡的材料。由密度的大小，规格的不同可分开使用。

Trends of Bolted Flange and Gasket in European Standard

欧洲螺栓法兰设计和垫片标准的新动向

3-D Finite Element Simulation of Bolted Flange Joint Considering Gasket Nonlinearity

考虑垫片非线性时法兰接头性能的三维有限元模拟

If parts of the crank drive were replaced, you must determine the new cylinder-head gasket again by measuring the piston projection in "tdc" position.

如果曲柄传动的零件已更换，则必须测量活塞在“tdc”位置的突出部分以重新确定新的气缸垫是否恰当。

MCR Cylinder Head Sealing Gasket-Research, Development and Application of Metal Compounded Rubber Sealing Material

MCR缸头垫&新型金属复合橡胶密封材料的研发与应用

The gasket cavity should face out to the adjoining flange.

垫圈的空穴应该面向临近法兰的外面.

For example, in order to prevent secondary pollution, even the use of sewage is not Valve asbestos packing and gasket sealing.

例如为了防止二次污染，即使是排污阀也不采用含石棉的密封填料和垫片。

Self-locking include self-locking teeth external blade, silicon rubber gasket, internal ring.

环切吻合器( 自锁 式)由含自锁齿外环刀口 、 硅橡胶垫环 、 内环构成.

The ring joint is self-aligning; the gasket maybe reused unless it is physically damaged.

这种环连接可 自行 调整对准; 除非出现物理损坏,否则垫圈可以重复使用.

The male and female joint confines the gasket O . D and I. D.

这种外螺纹和内螺纹连接限制了垫圈的外径和内径.

This connection has a left-hand thread ( loosens with clockwise rotation ) and requires a gasket to seal.

这种接头具有左手螺纹 ( 顺时针旋转为松开 ) ,要求使用垫圈来密封.

Remove the bezel and rubber gasket from the motor output shaft.

从马达输出轴上拆卸玻璃框和橡皮垫圈.

IP 65 when properly installed using the sealing gasket supplied ( without bezel ).

符合IP65当正确安装使用的密封垫圈供应 ( 不含面板 ).

Electrical insulating parts, seal gasket, non-adhesive material.

电绝缘零件, 密封衬垫, 防粘材料.

The oil-pan gasket fits between the oil pan and bottom pf the engine block.

石油潘垫片一刀切之间油底壳和底部酚醛引擎座.

When you install plate thickness 4.05 mm elastic gasket materials.

安设印版时拔取厚度为4.05毫米的不塑性垫材.

Remove the bolts and lift the pan off the manifolDiscard the gasket.

拆下螺栓并举高盘脱离歧管.扔掉衬垫.

Under no circumstances, can the lamp be covered with heat insulation gasket or similar materials.

不管什么情况下, 灯具都不能被隔热衬垫或类似材料盖住.