solidification的例句大全

Effects of the liquid structural change on crystallization orientation were investigated. It is found that the melt after the liquid structural change preferably grew on the high index crystal plane with the solidification process, which was responsible for the branching of low index single crystal plane.

液-液结构转变对晶体生长取向的影响主要是随凝固长度增加，液-液结构转变使合金实现高指数晶面取向，加剧了低指数晶面分支现象。

The diffuse speed and depth of Si element in rapid solidification brazing metal are higher than that in as-cast one.

快冷钎料中Si元素在母材中的扩散速度和深度都远高于普通铸态钎料。

With the solidification rate raised, the average grain size diminished and intensified the solute concentrations.

随着冷却速率的提高，使得材料的晶粒尺寸减小，溶质元素偏析程度加剧。

The theory of liquid metal die forging is the understanding of the process which combines solidification under high pressure with forced feeding by plastic deformation.

液态模锻理论是对高压下结晶凝固和塑性变形下强制补缩复合过程的认识。

Numerical Simulation of Mold Filling and Solidification and Experimental Analysis in Furnace Grate Investment Castings

炉排片熔模铸造充型与凝固过程的数值模拟及验证

Laser rapid forming ( LRF), a new solidification processing technology, has many advantages which would make it competitive for the processing of TC21 alloy.

激光快速成形作为一种材料凝固成形新技术，诸多优点使其成为一种具有竞争力的TC21钛合金成形方法。

Formation and Micro-Crystallization of In-Situ Bulk Amorphous ( ZrCuAl) AgY Alloy Composites SYNTHESIS OF PLASTIC Zr-BASED BULK METALLIC GLASS WITH CRYSTAL PHASE BY DIRECTIONAL SOLIDIFICATION

原位反应（ZrCuAl）AgY块体非晶复合材料的形成与微晶化机制研究定向凝固制备内生晶体增塑的锆基非晶复合材料

Numerical simulation of a1/ sic_p system two dimension solidification processing by centrifugal casting

离心力作用下Al/SiC p系统二维凝固过程的数值模拟

DTA method was employed to measure the undercooling of samples during solidification.

利用差热分析法测定了试样在相同冷却速度下的过冷度.

DTA method was employed to measure the undercooling of samples during solidification.

利用差热分析法测定了试样在相同冷却速度下的过冷度.

Finite Difference Method ( FDM ) is usually used for calculating the temperature field of casting solidification processes.

有限差分方法是凝固过程温度场解析的常用数值计算方法.

The presentation of MTC solidification research idea provide an approach of solving shrinkage and other defects.

并将其应用于凝固成形,提出了进一步研究设想,可提供新的解决收缩缺陷及其他缺陷的有效途径.

This paper introduces Mould-Temperature-Control ( MTC ) forming technology and the numerical simulation of its application in solidification process.

首先介绍了模具温控成形技术的方法和工艺. 然后具体到凝固成形,分析了其数值模拟的研究现状.

With the theoretical analysis, the computer simulation and the process experiment methods, this paper studies the liquid forming mechanism of silicon wafer for ELCC technology and makes provision for further research on the solidification microstructure control of the silicon sheet.

采用理论分析、计算机模拟与工艺实验相结合的方法，对ELCC技术硅片液态成形机制进行了研究，为进一步对硅片凝固过程组织控制的研究奠定基础。

EBIC results showed that the recombination properties of grain boundaries and dislocations were related to the solidification positions of ingot.

EBIC结果显示铸造多晶硅中晶界和位错的复合特性与晶锭的凝固位置有关。

Self-modification in EASA is attributed to the occurrence of a severe undercooling during solidification, which is related with the formation of homogeneous melt and the electric current in electrolysis process.

合金组织对冷却速度不敏感，具有遗传性，合金具有良好的韧性和塑性。电解Al-Si合金熔体为均质熔体，凝固时出现大的过冷度是形成变质组织的原因。

This paper presented the new method for solidification/ stabilization of mercury using chemically bonded phosphate ceramics-CBPC. The effect of sulfide and additive on CBPC has been explored.

本研究以实现汞废物的固化稳定化为目标，以CBPC&化学键磷酸盐陶瓷为固化基质材料，对含汞废物进行处理研究，探索了稳定剂硫化物、添加物S微粉对CBPC基质的影响。

The solidification microstructure of the stainless steel layer was typical coarse cellular dendrite crystal epitaxially from the mother sheet, and after rolling it changes to the fine equiaxed crystal.

凝固层轧制前为逆热流方向外延生长的粗大胞状树枝晶，轧制后为细小的等轴晶组织。

Numerical Simulation of Cellular/ Dendrite Arm Spacing Selection During Unidirectional Solidification of Ti-Al Alloy

Ti-Al合金定向凝固过程中胞/枝晶间距选择的计算机模拟

Progress of Dendritic Morphology Evolution during Solidification Process

凝固过程中枝晶组织形貌演变模拟进展