提出的例句大全

This article reviews the effect of tax benefit and gives advice to the reform of tax policy.

本文将在分析税收优惠政策的有效性及其带来的福利效应的基础上提出对税收政策改革的建议。

According to the law of crack development and mechanical index correlation analysis results, use the maximum bending force, shearing force and fracture energy as the main mechanical parameters, put forward the test design method.

基于裂缝动态发展规律与力学指标关联度分析结果，以最大弯曲力、层间剪切力和断裂能作为主要设计参数指标，提出配合比设计的试验方法。

Taking into account of the requirements in terms of aerodynamics, structural mechanics and aesthetics, automotive extrusion profiles are generally need to bend into a certain curvature. So it proposes a higher demand on surface quality and accuracy of the curved profile.

考虑到空气动力学、结构力学和美观等方面的要求，车身用挤压型材一般都需要弯曲成一定的曲率，从而对弯曲型材的表面质量和准确度提出了更高的要求。

Furthermore, the technique of benchmark test based on network attack description language ( NADL) is proposed.

进而，对网络欺骗系统的测试方法进行了研究，提出了一种基于攻击描述语言的基准测试技术。

A high performance ion chromatographic method is presented for the simultaneous determination of chloride and sulfate in cane or beet juice, syrup and molasses. Beet juice was used as raw materials in lactic acid fermentation research.

本文提出了用高效离子色谱法同时测定糖汁、糖浆及废蜜中的氯离子和硫酸根离子。以甜菜为原料，经榨汁处理，将所得原料进行乳酸发酵。

The selections of criteria of artificial bedding in the aspects of relative density, grain size, shape and electromagnetism were proposed;

从相对密度、粒度、形状及电磁性方面提出了人工床层的选定标准；

In the construction technology, the three-dimension drainage network is used to instead of the sand bedding course, and put into practice in field test area with actual engineering.

施工工艺中提出三维土工排水网替代砂垫层的新思路，结合实际工程在现场试验区加以实施。

Hence, a new question is raised how to consider the magnitude of tensile stress in the stability analysis of geotextile reinforced bedding course.

这对土工织物加筋垫层稳定分析中如何考虑拉应力大小提出了新的问题。

The mechanical fault of some large motor bearings are detected and analyzed, the corresponding improvement is proposed.

通过对某大型电动机轴承的故障检测及分析，提出了相应改进措施。

Based on the analysis, corresponding measures including retarding plate corrosion, improving scraper, fastening stand fire main, adding rust-resisting valve and auto-sewerage are introduced in detail.

提出了延缓罐底板腐蚀、改造刮板、固定消防立管、增设除渣阀、安装自动排水装置等具体改进措施。

Using the method of Differential Geometry, the decoupling control and complete linearization of the induction motor are realized, so a new control method for AC drive system is obtained.

本文采用非线性系统的微分几何方法实现交流异步电动机的解耦控制和完全线性化，为交流传动系统提出了一种新的控制方法。

This paper analysed briefly technical characteristic of different kinds of copper crude metallurgy and combined with productive practice of Yunnan Copper Industry Company. Application of oxygen enriched air top blowing bath smelting process to reconstruct copper crude metallurgy system have been put forward.

文章简要分析各种铜粗炼工艺特点，结合云南铜业股份有限公司生产实际，提出了采用富氧顶吹熔池熔炼法改造铜粗炼系统是较为合理的工艺方案。

Supposing that ramie stalk is made up of two kinds of different material ( bast fibre and xylem). But their differences of mechanical properties are ignored.

提出了三者的力学建模方法。假定苎麻茎秆是由韧皮纤维、木质部两种异质材料复合而成的复合材料，不考虑它们的性能差别。

Based on the Chirp Z transform, the paper proposes an approach to solve SRC by dividing the range dimension into blocks.

本文在基于Chirp z变换SAR成像算法的基础上，提出了一种对距离维进行分块处理解决二次距离压缩的方法。

By studying the weighing process composed of conveying belt and feeding gate, a new dynamic quantitative weighing control method is presented.

以传送带、料门给料的动态称重过程为对象，提出了一种新型动态定量称重控制方法。

In this paper, a divided driving circuit for stepping motor controlled by FPGA is put forward, based on the analysis of the principle of stepping motor divided driving.

在对步进电机细分驱动原理进行分析研究的基础上，提出一种基于FPGA控制的步进电机细分驱动器。

A measuring method using a vernier caliper to determine the error of position for evenly divided holes along a circle is introduced.

本文介绍采用游标卞尺测量圆周均布孔组位置度误差的方法，提出用极座标法和弦长法两种方法计算其误差值或验收公差。

This paper presents a new method of measuring the graduation angle of the equally divided circle by using 4 high precision inductive gauge heads to form a single constant angle.

本文提出一种用4个高精度电感测头构成单常角，实现对等分圆周分度角度测量的新方法。

In this paper, H foreign trade company of sports protective equipment are facing how to allocate limited resources to the right customers, This paper proposed a two-step customer classification method.

本文针对运动防护用品H外贸公司所面临的如何将有限的资源分配于合适的客户，提出了两步客户分类方法。

It is pointed out that the mechanical failing parameter of composite line post insulator with mechanical load bearer made of FRP elastomer material shall not be characterized with mechanical failing load as that for porcelain insulator but with maximum design bending load.

提出用环氧玻璃纤维芯棒作承力件，其机械破坏特性不宜按瓷绝缘子的额定机械破坏负荷来表征，应按照最大设计弯曲负荷表征。